Difference between revisions of "Equipment/Colchester Master Lathe"
Deanforbes (talk | contribs) |
|||
| (16 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
{{EquipmentInfobox | {{EquipmentInfobox | ||
| − | |name=Colchester Master | + | |name=Metal Lathe (Colchester Master) |
| − | |image= | + | |image=Colchester Master Lathe 2022-02-11.jpg |
|category=Equipment | |category=Equipment | ||
|subcat=Metalworking | |subcat=Metalworking | ||
| − | |status= | + | |status=Good working order |
|reqtraining=yes | |reqtraining=yes | ||
| + | |trainlink=[[Lathe Training]] | ||
|acnode=yes | |acnode=yes | ||
|origin=Donation | |origin=Donation | ||
|owner=LHS | |owner=LHS | ||
| − | |maintainers=Machine Shop Team | + | |maintainers=Machine Shop Team - lead is Toby |
| − | |location= | + | |location=Metalworking Shop |
}} | }} | ||
| + | This is a Colchester Master 3250 metal lathe, used for many kinds of turning operations on (mostly round) metal parts | ||
| − | + | The lathe is ACNode controlled and requires training. For information on the training process see [[Lathe Training]] | |
| − | + | For some information on the current range of tooling and accessories, see [[Metal Lathe Accessories]] | |
| − | + | A few house rules for using the lathe: | |
| + | * No wood (sawdust gets into all the moving parts, soaks up moisture and oil and then becomes quite abrasive) | ||
| + | * No use of compressed air for cleaning (it sometimes drives chips past the chip guards and into the moving parts) | ||
| − | + | When you are finished with the lathe please ensure all chips are removed from the ways and carriage - first by brushing down with a brush, then hoovering using the nearby wet & dry vacuum, then finally wiping down with a rag | |
| − | + | Metal Group - https://groups.google.com/forum/?hl=en-GB#!forum/london-hackspace-metal-working-group | |
| − | + | =Useful Specs= | |
| − | |||
| − | |||
| − | |||
| − | |||
| + | Toolholder: Dickson S2 (Tool holding slot 25 x 17mm) | ||
| + | Headstock Taper: MT5 | ||
| − | + | Parts List - https://wiki.london.hackspace.org.uk/view/File:2021_10_28_Colchester_3250_MASTER_-_NEW_LOOK_PARTS_LIST.pdf | |
| + | =Maintenance= | ||
| − | + | Check coolant levels preferably before the coolant pump stops pumping. If it reaches that point, the reservoir can take a little over ~20L of 5% coolant diluted down with tap water: measuring jug & funnel can be found atop the big blue plastic jerry can of concentrate under the bench in the toolstore. There's a white 5L jerry can nearby for premixing (and may contain leftover) 5% coolant. | |
| − | |||
Latest revision as of 10:28, 15 March 2023
| Metal Lathe (Colchester Master) | |
|---|---|
 | |
| Sub-category | Metalworking |
| Status | Good working order |
| Last updated | 15 March 2023 10:28:40 |
| Training requirement | yes |
| Training link | Lathe Training |
| ACnode | yes |
| Owner | LHS |
| Origin | Donation |
| Location | Metalworking Shop |
| Maintainers | Machine Shop Team - lead is Toby |
This is a Colchester Master 3250 metal lathe, used for many kinds of turning operations on (mostly round) metal parts
The lathe is ACNode controlled and requires training. For information on the training process see Lathe Training
For some information on the current range of tooling and accessories, see Metal Lathe Accessories
A few house rules for using the lathe:
- No wood (sawdust gets into all the moving parts, soaks up moisture and oil and then becomes quite abrasive)
- No use of compressed air for cleaning (it sometimes drives chips past the chip guards and into the moving parts)
When you are finished with the lathe please ensure all chips are removed from the ways and carriage - first by brushing down with a brush, then hoovering using the nearby wet & dry vacuum, then finally wiping down with a rag
Metal Group - https://groups.google.com/forum/?hl=en-GB#!forum/london-hackspace-metal-working-group
Useful Specs
Toolholder: Dickson S2 (Tool holding slot 25 x 17mm)
Headstock Taper: MT5
Parts List - https://wiki.london.hackspace.org.uk/view/File:2021_10_28_Colchester_3250_MASTER_-_NEW_LOOK_PARTS_LIST.pdf
Maintenance
Check coolant levels preferably before the coolant pump stops pumping. If it reaches that point, the reservoir can take a little over ~20L of 5% coolant diluted down with tap water: measuring jug & funnel can be found atop the big blue plastic jerry can of concentrate under the bench in the toolstore. There's a white 5L jerry can nearby for premixing (and may contain leftover) 5% coolant.