Difference between revisions of "Equipment/DrillPress"
Jump to navigation
Jump to search
(30 intermediate revisions by 9 users not shown) | |||
Line 1: | Line 1: | ||
− | + | {{EquipmentInfobox | |
+ | |name=Drill press <!-- Name of the item. --> | ||
+ | |image=Axminster ED16SB.jpg | ||
+ | |model=Axminster ED16SB<!-- Model --> | ||
+ | |category=Equipment <!-- Main category. Please leave alone to keep item in this category --> | ||
+ | |subcat=defunt | ||
+ | |status=Disposed of | ||
+ | |consumables=oil, cutting fluid,drive belt<!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. --> | ||
+ | |accessories=Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> | ||
+ | |reqtraining=No<!-- Is training required to use this equipment? Yes or no. --> | ||
+ | |trainlink=Unknown <!-- If training is required, provide a link to training signup or contact page. Otherwise leave blank. --> | ||
+ | |acnode=No<!-- Is the equipment ACnode locked? --> | ||
+ | |owner=LHS<!-- Provide a link to owners members page if other than LHS --> | ||
+ | |origin=Unknown <!-- If via pledge, please link to the completed pledge page on the wiki --> | ||
+ | |location=Woodshop | ||
+ | |maintainers=sjrapid<!-- NO LINKS PLEASE; it currently breaks the template. If someone is nominated as managing the upkeep of this item, please list them here. --> | ||
+ | |template_ver=1.1 <!-- Please do not change. Used for tracking out-of-date templates --> | ||
+ | }} | ||
+ | ==Status== | ||
+ | '''Works, but is not very precise!''' | ||
− | + | 9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out with a dial indicator. | |
− | + | ||
+ | Quill runout is approximately 0.2mm (should be <=0.02mm, 1thou) ). Runout at the chuck can be anything up to 10x this depending on selected speed and cutting bit. Your holes may be oval! | ||
+ | |||
+ | Here's the dial-indicator test video: | ||
+ | |||
+ | [http://www.flickr.com/photos/flux-org-uk/9469751707/ Drill press precision] | ||
+ | |||
+ | There is a [[Pledge:_Drill_Press|pledge]] running to get a new Drill Press for the space. | ||
+ | |||
+ | The space has an Axminster drill press. The keyless chuck only goes down to 2.7 mm, so for anything smaller you need a "[http://uk.farnell.com/multicomp/143-0127/pin-chuck-auto-3-jaw/dp/1518437 pin chuck]". | ||
+ | |||
+ | Or you can use the Dremel and mini-mill for high speed / light duty / precision stuff. | ||
+ | Ideal jobs : | ||
+ | |||
+ | Dremel | ||
+ | *High speed, tiny bits e.g. PCB drilling | ||
+ | |||
+ | Mini-Mill | ||
+ | * Milling plastic, small aluminium etc. | ||
+ | * Drilling jobs requiring accurate positioning - use the table positioning | ||
+ | |||
+ | Drill Press | ||
+ | * Most general purpose drilling jobs | ||
+ | |||
+ | ==Model== | ||
+ | * Make: Axminster | ||
+ | * Model: [http://www.axminster.co.uk/axminster-axminster-ed16sb-pillar-drill-prod719342/ ED16SB] | ||
+ | * Manual: [http://www.axminster.co.uk/downloads/700101_manual.pdf on the Axminster website] | ||
+ | |||
+ | == Pictures == | ||
+ | {| | ||
+ | |[[File:Drill_press_non_stock.jpg|thumb|The Hackspace drill press, from the front]] | ||
+ | |[[File:Drill_press_side.jpg|thumb|The Hackspace drill press, from the side]] | ||
+ | |[[File:Drill_press_other_side.jpg|thumb|The Hackspace drill press, from the other side]] | ||
+ | |} | ||
+ | |||
+ | ==Log== | ||
+ | #<lovelace_> The chuck for the new stand drill falls out easily | ||
+ | #<lovelace_> I can't see how it tightens up | ||
+ | #<artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard. | ||
+ | #<artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely | ||
+ | #<lovelace_> K, seems firmly in now | ||
+ | #9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out under no load with a dial indicator. Also tested with a new certified chuck and arbour (0.0012 TIR). Measured run out of about 0.25mm on the new chuck. TIR not measured on the existing keyless chuck. |
Latest revision as of 20:17, 23 March 2019
Status
Works, but is not very precise!
9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out with a dial indicator.
Quill runout is approximately 0.2mm (should be <=0.02mm, 1thou) ). Runout at the chuck can be anything up to 10x this depending on selected speed and cutting bit. Your holes may be oval!
Here's the dial-indicator test video:
There is a pledge running to get a new Drill Press for the space.
The space has an Axminster drill press. The keyless chuck only goes down to 2.7 mm, so for anything smaller you need a "pin chuck".
Or you can use the Dremel and mini-mill for high speed / light duty / precision stuff. Ideal jobs :
Dremel
- High speed, tiny bits e.g. PCB drilling
Mini-Mill
- Milling plastic, small aluminium etc.
- Drilling jobs requiring accurate positioning - use the table positioning
Drill Press
- Most general purpose drilling jobs
Model
- Make: Axminster
- Model: ED16SB
- Manual: on the Axminster website
Pictures
Log
- <lovelace_> The chuck for the new stand drill falls out easily
- <lovelace_> I can't see how it tightens up
- <artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard.
- <artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely
- <lovelace_> K, seems firmly in now
- 9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out under no load with a dial indicator. Also tested with a new certified chuck and arbour (0.0012 TIR). Measured run out of about 0.25mm on the new chuck. TIR not measured on the existing keyless chuck.