Difference between revisions of "Equipment/DrillPress"

From London Hackspace Wiki
Jump to: navigation, search
m (Correcting non-standard form status entry "working order" to "faulty". "Good working order" sounds inappropriate due to tolerance issues.)
m
Line 1: Line 1:
 
{{EquipmentInfobox
 
{{EquipmentInfobox
 
|name=Drill press <!-- Name of the item. -->
 
|name=Drill press <!-- Name of the item. -->
|image=Drill press.jpg <!-- Image of the item. Leave with placeholder image if none exists. -->
+
|image=Axminster ED16SB.jpg
 
|model=Axminster ED16SB<!-- Model -->
 
|model=Axminster ED16SB<!-- Model -->
 
|category=Equipment <!-- Main category. Please leave alone to keep item in this category -->
 
|category=Equipment <!-- Main category. Please leave alone to keep item in this category -->
|subcat=Fabrication <!-- Sub-category if one exists. Please check main listing to see other categories contained within the main one -->
+
|subcat=Woodworking
 
|status=Faulty
 
|status=Faulty
 
|consumables=oil, cutting fluid,drive belt<!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. -->
 
|consumables=oil, cutting fluid,drive belt<!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. -->
Line 13: Line 13:
 
|owner=LHS<!-- Provide a link to owners members page if other than LHS -->
 
|owner=LHS<!-- Provide a link to owners members page if other than LHS -->
 
|origin=Unknown <!-- If via pledge, please link to the completed pledge page on the wiki -->
 
|origin=Unknown <!-- If via pledge, please link to the completed pledge page on the wiki -->
|location=Basement, workshop<!-- Floor, room/zone and location within that area -->
+
|location=Woodshop
 
|maintainers=sjrapid<!-- NO LINKS PLEASE; it currently breaks the template. If someone is nominated as managing the upkeep of this item, please list them here. -->
 
|maintainers=sjrapid<!-- NO LINKS PLEASE; it currently breaks the template. If someone is nominated as managing the upkeep of this item, please list them here. -->
 
|template_ver=1.1 <!-- Please do not change. Used for tracking out-of-date templates -->
 
|template_ver=1.1 <!-- Please do not change. Used for tracking out-of-date templates -->

Revision as of 19:27, 2 January 2016

Drill press
Axminster ED16SB.jpg
Model Axminster ED16SB
Sub-category Woodworking
Status Faulty
Last updated 23 March 2019 20:17:39
Consumables oil, cutting fluid,drive belt
Accessories Unknown
Training requirement No
Training link Unknown
ACnode No
Owner LHS
Origin Unknown
Location Woodshop
Maintainers sjrapid

Status

Works, but is not very precise!

9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out with a dial indicator.

Quill runout is approximately 0.2mm (should be <=0.02mm, 1thou) ). Runout at the chuck can be anything up to 10x this depending on selected speed and cutting bit. Your holes may be oval!

Here's the dial-indicator test video:

Drill press precision

There is a pledge running to get a new Drill Press for the space.

The space has an Axminster drill press. The keyless chuck only goes down to 2.7 mm, so for anything smaller you need a "pin chuck".

Or you can use the Dremel and mini-mill for high speed / light duty / precision stuff. Ideal jobs :

Dremel

  • High speed, tiny bits e.g. PCB drilling

Mini-Mill

  • Milling plastic, small aluminium etc.
  • Drilling jobs requiring accurate positioning - use the table positioning

Drill Press

  • Most general purpose drilling jobs

Model

Pictures

The Hackspace drill press, from the front
The Hackspace drill press, from the side
The Hackspace drill press, from the other side

Log

  1. <lovelace_> The chuck for the new stand drill falls out easily
  2. <lovelace_> I can't see how it tightens up
  3. <artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard.
  4. <artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely
  5. <lovelace_> K, seems firmly in now
  6. 9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out under no load with a dial indicator. Also tested with a new certified chuck and arbour (0.0012 TIR). Measured run out of about 0.25mm on the new chuck. TIR not measured on the existing keyless chuck.