Difference between revisions of "Equipment/OldVinylCutter"
(Update consumables, add note about cutting paper.)
(→T-Shirts: Update link to Heat Press)
|Line 187:||Line 187:|
= T-Shirts =
= T-Shirts =
You can heat press designs onto t-shirts using the [[
You can heat press designs onto t-shirts using the [[|]]
= Consumables =
= Consumables =
Revision as of 10:05, 2 June 2015
- 1 Instructions
- 2 Software
- 3 Specification
- 4 T-Shirts
- 5 Consumables
- 6 Old Vinyl Cutter
Please read Jinka 721 user manual for more information.
- No magnetic devices should be placed in the vicinity of the plotter, specifically the carriage.
- Don't leave pinch rollers pressed down while machine is not in use.
- Don't move the carriage manually.
- Don't touch carriage, metal roller, cutter and all moving devices when the machine is working.
- Don't press top beam or lift up black rail.
- Paper can be cut only when using self adhesive cutting mat.
Adjust the palce of pinch rollers according to paper width
Cutting plotter has 2 rollers and they can be moved along the guide rail. The handles of pinch rollers must be lifted before moving pinch rollers, hold the back of the roller and push it to the left or the right. Please don't pull the roller bars in the front, otherwise the machine precision will be affected.
The place of the rollers must ensure:
- Pinch rollers should be in the place out of the scope of the pattern.
- Pinch rollers should be 10 to 50mm away from the edges of the vinyl.
- Pinch rollers shouldn't be let down on the conjunction of two connexting metal rollers.
Loading the paper
- Lift the pinch-roller handles and let it away from metal rollers.
- Insert the vinyl between metal rollers and pinch rollers of the machine from behind to front.
- Align the front of the vinyl before cutting, since if vinyl is not well placed, serious deviation will occur. Ensure that vinyl is aligned by checking a straight side edge on front and back rulers.
- Carefully check the vinyl before cutting: serious deviation will occur if vinyl is not well placed. If the vinyl is uneven lift the pinch rollers on one side to adjust and then press down pinch rollers. It is necessary to trial run vinyl several times to attain minimum deviation before cutting work.
- Turn on the machine. The carriage should move to the right side and the metal roller will rotate automatically, thus complete the automatic reset. If it fails to reset, press the RESET key.
- At the same time when turning on, cutter bracket will be raised about 2 mm. Pressing ORIGIN key will make it fall down. Release the key to again raise the bracket. This shows the carriage and bracket are functioning properly.
If the machine is required to cut from an appointed location, press OFFLINE key. The yellow light will turn on. Press ← or → to move the carriage left or right. Press ↓ or ↑ to move the vinyl forward or backward. Now press the ORIGIN and the machine will work from the point at which the blade is located.
Test Cut and Force Adjustment
Once the blade or plotter is installed and the vinyl is inserted, preliminary test-cut should be carried out to check if the force of the blade or plotter is acceptable. To do so, press the TEST key.
Use F+ or F- to increase or decrease cutting force. Force should be enough to cut cleanly through vinyl but not the backing material. If the force is too high the blade and pressing strip could be damaged. The protruding portion of the blade tip should be about 0.5mm or less—length normaly is 2/3 of the thickness of the vinyl. First try using low force and increase to the optimal value.
Caution: Always test cut every time you use a new type of vinyl to check the cutting force.
The Windows and Linux drivers are on the Whittenstein usb card that is attached to the machine.
We've currently been unable to get the FTDI Virtual Com Port drivers working with the cutter under OSX Mavericks. If you have success with OSX, please update this page.
Download Inkscape, move items in the driver folder from USB card into: /home/.config/inkscape/extensions
Run inkscape and should be there under extensions, cutter/plotter.
(Tested on Windows 8.1 using Inkscape 0.91. If you got it working on Mac OS or GNU/Linux please update this page.)
In Inkscape go to "Extensions -> Export -> Plot...". Update your settings to match the following. Settings that are different from default are printed in bold.
- Serial port: COM1 (Might be different. On GNU/Linux something like: '/dev/ttyUSB0')
- Serial boud rate: 9600
- Flow control: Hardware (RTS/CTS)
- Command language: HPGL
- Resolution X (dpi): 1002,0
- Resolution Y (dpi): 1002,0
- Pen number: 1
- Pen force (g): 0
- Pen speed (cm/s or mm/s): 0
- Rotation (°, clockwise): 0
- (Unchecked) Mirror X axis
- (Unchecked) Mirror Y axis
- (Unchecked) Center zero point
- Overcut (mm): 1,00
- Tool offset (mm): 0,25 (0,00 when using a Pen for plotting)
- Use precut: Checked
- Curve flatness: 1,2
- Auto align: Checked
Make your objects to path:
- Edit -> Select All (Ctrl+A)
- Path -> Object to Path (Shift+Ctrl+C)
Start cutting: Extensions -> Export -> Plot... -> Apply
Linux: Writing to serial port
The vinyl cutter will happily take HPGL piped over serial, eg in Linux:
cat filename.hpgl > /dev/ttyUSB0
Make sure you have write permissions for the ttyUSB0 device, a quick temporary hack for this is:
sudo chmod 0777 /dev/ttyUSB0
Note: If you have multiple USB serial devices, the cutter may not be ttyUSB0
What you use to make the HPGL is up to personal preference. Inkscape can export as HPGL, and has plugins for both Linux/OSX (InkCut) and Windows (Inkscape CAMM-GL) to help fine tune cuts.
Note: Inkscape 4.9+ generates large HPGL with all the coordinates as a single line. This buffer overflows the black vinyl cutter causing it to crash. Smaller designs may be fine, otherwise manually add a carriage return after each instruction by using a text editor.
Protip in vi:
|Max Paper Width||720mm|
|Max Plotting Width||630mm|
|Gross Weight||25 kg|
|Packing Size||96 x 35 x 43 cm|
|Interface||Serial Port & USB Port ( Optional )|
|Max Plotting Speed||800mm/s|
|Max Cutting Force||500g|
|Cutting Tool||Imported Hardness Alloy Steel Blade|
You can heat press designs onto t-shirts using the Heat Press.
You can cut vinyl, plot on paper using a pen. Paper and cards can only be cut when using self adhesive cutting mat.
Old Vinyl Cutter
The old cutter is in the space but is not functional Equipment/VinylCutterOld