Difference between revisions of "Equipment/Staubli/J11"

From London Hackspace Wiki
Jump to: navigation, search
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
 +
== General ==
 
The J11 connector on the back of the Staubli controller contains the digital IO lines.
 
The J11 connector on the back of the Staubli controller contains the digital IO lines.
  
Line 5: Line 6:
 
The outputs are isolated, normally open, relay contacts, maximum rating at 125v @ 1A. Outputs 7 & 8 are used in the arm to control the gripper solenoids.  
 
The outputs are isolated, normally open, relay contacts, maximum rating at 125v @ 1A. Outputs 7 & 8 are used in the arm to control the gripper solenoids.  
  
The inputs are opto-isolation 24v LED inputs. LOW = 0v-3v. HIGH = 10-24v. As they are LED opto-isolators, they only work with the correct polarity.
+
The inputs are opto-isolation 24v LED inputs. LOW = 0v-3v. HIGH = 10-24v. As they are LED opto-isolators, they only work with the correct polarity. The manual states that you should use your own isolated, regulated power supply.
 +
 
 +
Inputs 1, 2 & 3 (and 4? depending on which manual you read) can be configured as "fast" inputs, with a response time of 1ms. All the other inputs have a 16ms response time.
  
 
The outputs can be activated and deactivated in V+ like this :
 
The outputs can be activated and deactivated in V+ like this :
Line 24: Line 27:
 
* Page 50 – [https://www.dropbox.com/s/d8w0m5gdf8hc4sn/UserManual_CS7M_Jul97_V0.0_EN.pdf CS7 User Guide]
 
* Page 50 – [https://www.dropbox.com/s/d8w0m5gdf8hc4sn/UserManual_CS7M_Jul97_V0.0_EN.pdf CS7 User Guide]
  
 +
== Pinout ==
 
[[File:StaubliJ11.png|left]]
 
[[File:StaubliJ11.png|left]]
  

Latest revision as of 14:24, 17 February 2015

General

The J11 connector on the back of the Staubli controller contains the digital IO lines.

There are 6 relay outputs and 12 digital inputs. The connector can also supply 24v power.

The outputs are isolated, normally open, relay contacts, maximum rating at 125v @ 1A. Outputs 7 & 8 are used in the arm to control the gripper solenoids.

The inputs are opto-isolation 24v LED inputs. LOW = 0v-3v. HIGH = 10-24v. As they are LED opto-isolators, they only work with the correct polarity. The manual states that you should use your own isolated, regulated power supply.

Inputs 1, 2 & 3 (and 4? depending on which manual you read) can be configured as "fast" inputs, with a response time of 1ms. All the other inputs have a 16ms response time.

The outputs can be activated and deactivated in V+ like this :

SIGNAL 1                  // turns relay output 1 on
SIGNAL -1                 // turns relay output 1 off
SIGNAL 1,2,3,4,5,6        // turns relays 1-6 all on
SIGNAL -1,-2,-3,-4,-5,-6  // turns relays 1-6 all off

The inputs are used in V+ like this :

WAIT SIG(1001)            // this pauses the V+ program until input 1 is activated and then continues.

CS7 back.jpg

The connector has 50 pins, in three rows. Refer to the following manuals for details and schematics :

Pinout

StaubliJ11.png
Pin# Description
1 O1+ (Output 1 relay contacts)
2 O1- (Output 1 relay contacts)
3 O2+ (Output 2 relay contacts)
4 O2- (Output 2 relay contacts)
5 O3+ (Output 3 relay contacts)
6 O3- (Output 3 relay contacts)
7 O4+ (Output 4 relay contacts)
8 O4- (Output 4 relay contacts)
9 O5+ (Output 5 relay contacts)
10 O5- (Output 5 relay contacts)
11 O6+ (Output 6 relay contacts)
12 O6- (Output 6 relay contacts)
13 I1+ (Input 1 positive)
14 I1- (Input 1 negative)
15 I2+ (Input 2 positive)
16 I2- (Input 2 negative)
17 I3+ (Input 3 positive)
18 I3- (Input 3 negative)
19 I4+ (Input 4 positive)
20 I4- (Input 4 negative)
21 I5+ (Input 5 positive)
22 I5- (Input 5 negative)
23 I6+ (Input 6 positive)
24 I6- (Input 6 negative)
25 I7+ (Input 7 positive)
26 I7- (Input 7 negative)
27 I8+ (Input 8 positive)
28 I8- (Input 8 negative)
29 I9+ (Input 9 positive)
30 I9- (Input 9 negative)
31 I10+ (Input 10 positive)
32 I10- (Input 10 negative)
33 I11+ (Input 11 positive)
34 I11- (Input 11 negative)
35 I12+ (Input 12 positive)
36 I12- (Input 12 negative)
37 NC / unknown
38 NC / unknown
39 NC / unknown
40 NC / unknown
41 NC / unknown
42 NC / unknown
43 24v power
44 24v power
45 NC / unknown
46 NC / unknown
47 NC / unknown
48 NC / unknown
49 NC / unknown
50 NC / unknown
Shell / Shield Ground