Difference between revisions of "Gantry CNC"
Jump to navigation
Jump to search
| Line 11: | Line 11: | ||
|trainlink=<!-- If training is required, provide a link to training signup or contact page. Otherwise leave blank. --> | |trainlink=<!-- If training is required, provide a link to training signup or contact page. Otherwise leave blank. --> | ||
|acnode=Yes <!-- Is the equipment ACnode locked? --> | |acnode=Yes <!-- Is the equipment ACnode locked? --> | ||
| − | |owner=LHS <!-- Provide a link to owners members page if other than LHS --> | + | |owner=LHS (spindle and VFD currently on loan) <!-- Provide a link to owners members page if other than LHS --> |
|origin=LHS Built<!-- If via pledge, please link to the completed pledge page on the wiki --> | |origin=LHS Built<!-- If via pledge, please link to the completed pledge page on the wiki --> | ||
|location=Basement, Robotics area<!-- Floor, room/zone and location within that area --> | |location=Basement, Robotics area<!-- Floor, room/zone and location within that area --> | ||
| Line 17: | Line 17: | ||
|template_ver=1.1 <!-- Please do not change. Used for tracking out-of-date templates --> | |template_ver=1.1 <!-- Please do not change. Used for tracking out-of-date templates --> | ||
}} | }} | ||
| + | == Summary == | ||
| + | |||
| + | We made this CNC from the donated linear slides and stages, and other things lying around the space, and some bits and pieces that members had. All suggestions for improvements / modification are welcome! | ||
| + | |||
== Specs == | == Specs == | ||
* Spindle 1000 to 20000rpm | * Spindle 1000 to 20000rpm | ||
| − | * Rapid traverse rate at 100% 2000mm/min | + | * Rapid traverse rate at 100% 2000mm/min |
* Axis travel | * Axis travel | ||
**X(longitudinal) 800mm | **X(longitudinal) 800mm | ||
** Y(cross) 960mm | ** Y(cross) 960mm | ||
** Z(vertical) 80mm (Phase 1), 280mm (Phase 2) | ** Z(vertical) 80mm (Phase 1), 280mm (Phase 2) | ||
| + | |||
| + | == Technical == | ||
| + | |||
| + | The system currently runs GRBL 0.9 and is very similar to use to the [https://wiki.london.hackspace.org.uk/view/Equipment/Shapeoko2 Shapeoko2]. | ||
| + | |||
| + | To start the spindle, press the green button on the VFD. Use the up and down keys to vary the speed. | ||
Revision as of 04:02, 8 September 2015
| Gantry CNC | |
|---|---|
 | |
| Model | LHS Design |
| Sub-category | CNC |
| Status | Under construction |
| Consumables | Router / Milling Cutters |
| Accessories | NA |
| Training requirement | Yes |
| ACnode | Yes |
| Owner | LHS (spindle and VFD currently on loan) |
| Origin | LHS Built |
| Location | Basement, Robotics area |
| Maintainers | Robotics, Metalbashers |
Summary
We made this CNC from the donated linear slides and stages, and other things lying around the space, and some bits and pieces that members had. All suggestions for improvements / modification are welcome!
Specs
- Spindle 1000 to 20000rpm
- Rapid traverse rate at 100% 2000mm/min
- Axis travel
- X(longitudinal) 800mm
- Y(cross) 960mm
- Z(vertical) 80mm (Phase 1), 280mm (Phase 2)
Technical
The system currently runs GRBL 0.9 and is very similar to use to the Shapeoko2.
To start the spindle, press the green button on the VFD. Use the up and down keys to vary the speed.