NOTE: IMPORTANT: THIS IS THE OLD HACKSPACE!!!!
Lab24 has a number of network points, wired across the false ceiling. These terminate in the quiet/class room cabinet.
The space's dns zone is lan.hack.rs. NB if you change this you'll need to update SNMP in cacti. Our IP range (assigned in ChaosVPN) is 172.31.24.0/23.
We use 172.31.24.0/24 on the lan, 172.31.25.0/24 is currently unused.
For ipv6 we've got 2001:470:92f1::/48 and we use 2001:470:92f1::/64 on the lan. We used to use 2001:470:92f1:a000::/60 for the cerowrt box but don't anymore. Those are he.net ranges, owned by User:Ms7821
All these diagrams are wrong.
sw/n is switch port n
Mac addresses without names where unknown at the time the diagram was generated.
Port 24 has the fonera on it, which is why it has so many things.
No, i don't know why babbage has 2 mac addresses.
Layer 3 (ipv4)
Our internet is the Be Pro service:
IP: 188.8.131.52 Netmask: 255.255.255.0 Gateway: 184.108.40.206 DNS 1: 220.127.116.11 DNS 2: 18.104.22.168
We use a Draytek Vigor 120 modem which simply bridges the ADSL to ethernet. You can access this at http://192.168.2.1 (no username/password). The Internet light doesn't come on, presumably because it's in bridge mode. NB it doesn't like the LAN port being disconnected: doing it twice in short succession will cause it to stop responding to traffic on that port (presumably some weird arp issue). Restart both the router and modem at the same time to prevent this.
In addition to the Fonera (and probably replaceing it?) we have a Netgear 3700v2 donated by Dave Täht of the bufferbloat project. It runs a custom build of OpenWRT called CeroWRT please see that page for builds and installation instructions.
IP prefix: 2001:470:92f1::/48
As an experiment, we block inbound IPv6 except for port 22 (ssh), on the assumption that most people don't even realise IPv6 is on. Please shout if you actually need inbound connections to the space. DNS isn't enabled yet.
We've got a Cerowrt box to test. It's routing the subnets 172.31.25.0/24 and 2001:470:92f1:a::/60.
IP: 172.31.24.10 IPv6: 2001:470:92f1::3
We also have a Netgear WNDR3700v2 (thin black box on top of the rack). - this used to run cerowrt but has now been changed to OpenWRT - CeroWRT want's to route everything which isn't useful for us and also it was using SSID's that no-one used. It does 802.11an on 5Ghz. config interface here. The reg domain was 'fixed' to support GB properly using this guide. If you have problems with 5Ghz just switch this access point off and tell the mailing list that you have done so! :)
We have 2 ssid's:
LondonHackspace - WPA2PSK, you can find the key written on posters on the walls of the rooms in the hackspace.
spacenet - currently experimental and unfinished spacefed deployment.
3com (always on), in the space dns zone as 'switch'. The switch is a 3CR17501-91, and is at 172.31.24.2. Please don't play.
Replaced with a pair of HP ProCurve 2848's.
They are connected together via a 2 port trunk on ports 47 and 48.
They run different versions of the firmware, and should probably be upgraded sometime.
We also have 2 small unmanaged switches, one is under the laser cutter for coolbot and layz0rs, and one is by the smaller touchtable and was used for the stratasys. Both should be replaceable (or almost replaceable) by the new cabling.
We also have 2 more Cisco switches, a 3560 Poe-24 (24 port + 2 x gigabit sfp's) and a 2550 (24 port, 2 x gigabit gbics). We have copper SFP's but the copper gbics we've got don't fit in the switch!, see cisco3 & cisco4. We have fibre sfp's and some bits of fibre instead.
- Babbage monitoring, IRC, storage, general purpose server (always on)
- Bell The door/building management controller (always on)
Flowers The door/building management controller (always on)
- Lovelace Makerbot
Flowers Media PC (currently unused)
- Patel laser cutter (hackspaceremote/hackspace maps to password-less user hackspace)
- Postel The SGI O2
- Difference Desktop PC
- Touch table PC
Outside Lab24: Turing Bitfolk VM
Working on the network
All members have access to the servers, and with that, the ability to make changes. It's crucial to remember that this is a shared network and any changes you make will affect others. In particular, please don't install updates or restart machines without a good reason and checking on IRC first.
Each piece of hardware will have its own logbook page on the wiki, where you should log significant changes and problems.
A list of things that could be done to make the network better.
- Look into why there are speed and duplex issues between the modem and church
* Simple fix is to add a new VLAN on the switch, and stick two ports in it. Should prevent any issues with autoneg between devices. * But would create other issues with having the internet side patched into the switch making it more liable to breakage through patching errors
- Alix board has N-spec minipci card in it but the kernel needs recompiling to allow us to use it on EU frequencies
- Wifi dropping packets
- Look into using QoS.
- Simultaneous 5/2.4GHz N WiFi.
* Airport Extreme * Cisco-Linksys Maximum Performance E4200 * Keep the Cisco for 2.4GHz and get a dedicated 5Ghz
- This page is fairly out of date (e.g. missing the ubiquti thingy), update it
- syslog server
- church upgrade
- sort out the switches
- finish physical cabling.
- ^-- those 3 depend on finishing the ebay stuff...