Difference between revisions of "Lulzbot Mini"
Chomiliert (talk | contribs) m |
(hint about flushing) |
||
| (6 intermediate revisions by 4 users not shown) | |||
| Line 5: | Line 5: | ||
|category=Equipment | |category=Equipment | ||
|subcat=CNC | |subcat=CNC | ||
| − | |status= | + | |status=[https://london.hackspace.org.uk/members/tools.php Check the Tools Status Page] |
|consumables=XT filament | |consumables=XT filament | ||
|accessories=Print removal knife | |accessories=Print removal knife | ||
| Line 14: | Line 14: | ||
|origin=Donation from Lulzbot | |origin=Donation from Lulzbot | ||
|location=3D printer area, Ground floor | |location=3D printer area, Ground floor | ||
| − | |maintainers= | + | |maintainers=tgreer, Welshie |
}} | }} | ||
=== Hull === | === Hull === | ||
| Line 20: | Line 20: | ||
Accessible via http://hull from inside the hackspace network. | Accessible via http://hull from inside the hackspace network. | ||
==== Filament ==== | ==== Filament ==== | ||
| − | Only use the provided | + | Only use the provided filament. |
Hull will theoretically print the follow filaments: | Hull will theoretically print the follow filaments: | ||
| − | * | + | * PLA |
| − | * | + | * ABS |
| − | * XT | + | * ''XT'' |
| − | * | + | * Nylon |
| − | + | Always use the correct slicing profile for the filament material you are using. Different filaments have different melting and burning points, so getting the wrong material type can end up with a scorched mess, or a failure to extrude with a strained extruder motor. Beware that ABS is alphabetically first on the drop-down but less likely to be used. | |
| + | please contact the maintainers if you wish to use a filament that is not available. | ||
| + | |||
| + | There is no need to use Pritt Stick, or other adhesive, to get the print to adhere to the bed with rigid filament. Applying excessive Pritt Stick merely cakes the bed in gunk, making the first few layers of your print look messy and lumpy. If you find the bed like this, it can be cleaned off with a warm soapy sponge. | ||
| + | |||
| + | When changing filaments between different plastic types with different melting points, manually select the tool temperature to be the hotter of the two when flushing out the remains, or you will find that the lower temperature filament can't push through the remains of the filament that may be left in the hotend or nozzle. | ||
= Cost = | = Cost = | ||
| − | Using the printers costs £1.50/hour of printing + 50p/meter of filament. Octoprint gives you both of these. | + | Using the printers costs £1.50/hour of printing + 50p/meter of filament. [[3D_Printing/Print_via_Octoprint|Octoprint]] gives you both of these. |
= Training = | = Training = | ||
Revision as of 15:03, 1 August 2019
| Lulzbot 1 (Hull) | |
|---|---|
 | |
| Model | Lulzbot Mini Standard Extruder |
| Sub-category | CNC |
| Status | Check the Tools Status Page |
| Last updated | 21 February 2022 13:37:43 |
| Consumables | XT filament |
| Accessories | Print removal knife |
| Training requirement | yes |
| Training link | https://wiki.london.hackspace.org.uk/view/Lulzbot_Mini_Training |
| ACnode | yes |
| Owner | Hackspace |
| Origin | Donation from Lulzbot |
| Location | 3D printer area, Ground floor |
| Maintainers | tgreer, Welshie |
Hull
Hull is a Lulzbot Mini Standard.
Accessible via http://hull from inside the hackspace network.
Filament
Only use the provided filament.
Hull will theoretically print the follow filaments:
- PLA
- ABS
- XT
- Nylon
Always use the correct slicing profile for the filament material you are using. Different filaments have different melting and burning points, so getting the wrong material type can end up with a scorched mess, or a failure to extrude with a strained extruder motor. Beware that ABS is alphabetically first on the drop-down but less likely to be used.
please contact the maintainers if you wish to use a filament that is not available.
There is no need to use Pritt Stick, or other adhesive, to get the print to adhere to the bed with rigid filament. Applying excessive Pritt Stick merely cakes the bed in gunk, making the first few layers of your print look messy and lumpy. If you find the bed like this, it can be cleaned off with a warm soapy sponge.
When changing filaments between different plastic types with different melting points, manually select the tool temperature to be the hotter of the two when flushing out the remains, or you will find that the lower temperature filament can't push through the remains of the filament that may be left in the hotend or nozzle.
Cost
Using the printers costs £1.50/hour of printing + 50p/meter of filament. Octoprint gives you both of these.
Training
Training is required. There is a cost of £5 to be trained (waived if trained on the old printer), payable to the trainer.
Logging
All prints are to be logged via : http://goo.gl/forms/ARNWXexh7zXHSq8p1