Project:Sanguinololu Thermocouple

From London Hackspace Wiki
Revision as of 19:56, 12 November 2012 by Pinski1 (talk | contribs)
Jump to navigation Jump to search
[[|Sanguinololu Thermocouple]]
Created 03/11/2012
Version 1
Members Pinski1
Project Status Awaiting PCBs
QR code


I wanted to add a thermocouple to my 3D printer's hot end. Ideally it would improve the quality of my printed objects as it would provide more accurate temperature readings with greater immunity from electronic noise generated by the stepper motors.


The PCB I have designed has the following features:

  • Fits onto the expansion headers already present on the Sanguinololu
  • Adds a MAX31855 thermocouple to digital convertor chip
  • Enables temperature readings between -200°C to +1350°C ±2°C
  • Has a resolution of 0.25°C
  • Can sample at 10Hz



Sanguinololu Thermocouple Schematic.png

The Eagle 5.11 schematic file.

PCB Layout

Sanguinololu Thermocouple Layout.png

The Eagle 5.11 board file.

Bill of Materials

Qty Value Ident Description
1 TXB0104D IC1 SOIC14 Bi-Directional level translator chip
1 TPS73033DBVT IC2 Could be any SOT23-5 +3V3 voltage regulator
1 MAX31855KASA+ IC3 SOIC8 Thermocouple-to-Digital chip
2 2.2uF C1, C2 Ceramic 1206 decoupling capacitors
3 10nF C3, C4, C5 Ceramic 0805 decoupling capacitors
1 SV1 2x5 way, straight, 2.54mm, female header
1 X1 2way, screw terminal, 5.08mm
1 Thermocouple, K Type


Top Bottom
Sanguinololu PCB top eagle.png Sanguinololu PCB bottom eagle.png The Eagle CAD layout.
Sanguinololu PCB Render.png The Eagle CAD 3D render
Sanguinololu PCB top.png Sanguinololu PCB bottom.png The PCB renders of OSH Park
To come To come The delivered PCBs.

How to Build

Tools required:

  • soldering iron
  • solder
  • tweezers

Tools that would be useful:

  • solder sucker
  • solder wick
  • magnifier


  1. Start by soldering the MAX31855KASA+ into position. Ensure pin 1 is correct and all the pins are lined up.
  2. Next solder in the TXB0104B, agin ensure pin 1 is correct and the pins line up.
  3. Solder in the final IC the +3V3 reg. This is the smallest package so special care will need to be taken to ensure the pins like up correctly.
  4. With the ICs done now solder in the passives. Start with the larger 1206 2.2uF capacitors, these will only fit in two places.
  5. Then solder in the smaller 0805 10nF capacitors, there should be 3 of these.
  6. With the surface mount components in place put the 2x5way female header such that it points out the bottom of the board (see the render) and solder it.
  7. Finally solder in the 2way screw terminals


You will need a Bus Pirate or something equivalent to communicate with the board and a K type thermocouple to sense the temperature.

The header to interface with a Sanguinololu has the following pin out:

Function Pins Function
Chip Select 1 2 NC
GND 5 6 NC
+5V 9 10 MISO

Connect your debug device (Arduino or Bus Pirate) to this using the standard connections. The board is +3V3/+5V tolerant.

Bus Pirate

If you have a bus pirate you will need to select SPI mode, then...

/To be done/


You will need to upload the following sketch to your Arduino in order to read the temperatures.

/To be done/

Adding to your 3D printer


This design is licensed under Creative Commons BY-NC-SA

This design is modified from Sanguinololu SD