|
|
| (8 intermediate revisions by 6 users not shown) |
| Line 1: |
Line 1: |
| [[File:Roland (Large).jpg|thumb|right]]
| | We're getting thin on the ground when it comes to vinyl so I think it's time to order some more. |
|
| |
|
| Model is a Roland CAMM-1 PNC-950. It hold up to 610mm (24") media and cuts up to 584mm ( ~23"). Length is essentially unlimited as it can use roll-feed media but seems to be restricted to 25m.
| | This is a pledge for a 50m roll of Hackspace (ultramarine) blue matte vinyl as this is commonly the colour most used. |
|
| |
|
| Manual: http://www.signcutpro.com/files/man/roland/pnc950.pdf
| | With the current offers a roll costs £55 + £10 delivery + VAT. |
|
| |
|
| FAQ: http://support.rolanddga.com/Docs/Documents/departments/Product%20Management/Product%20Information/Specialty%20Products/PNC950_FAQ.pdf
| | http://www.thevinylcorporation.co.uk/this-months-special-offers/avery-matt-110-pm-all-colours |
| | |
| | |
| The cutter is being donated by Tomwardill, with a small stock of vinyl. However, we will need more and Tom would appreciate donations towards the cost of his larger stocks. Please indicate if you can help.
| |
| | |
| ==Operation==
| |
| | |
| I have had a certain amount of success running the cutter with a serial connection from Inkscape under Linux. More messing around is needed.--[[User:Artag|Artag]] 13:32, 19 August 2010 (UTC)
| |
| | |
| * Sometimes the cutter refuses to print or respond to any buttons. This hasn't happened since I opened a door in the bottom of the printer and poked an EPROM there, so may be due to some poor internal connection.
| |
| | |
| * The serial cable (blue, with a 25WD at one end and a 9WD at the other) is connected as follows :
| |
| | |
| {|border="1" cellpadding="5" cellspacing="0"
| |
| |-
| |
| |Cutter, 25 pin male D ||PC, 9 pin female D||Use
| |
| |-
| |
| |pin 2 || pin 2 || PC RXD from cutter
| |
| |-
| |
| | 3 || 3 || PC TXD to cutter
| |
| |-
| |
| | 4 || n/c || cutter pin 5, RTS CTS loopback
| |
| |-
| |
| | 5 || n/c || cutter pin 4, RTS CTS loopback
| |
| |-
| |
| | 7 || 5 || ground
| |
| |-
| |
| | 20 || 8 || cutter DTR to PC CTS, flowcontrol
| |
| |}
| |
| | |
| This provides for hardware (rts/cts) handshake. Software flowcontrol may be OK but the cutter manual suggests overrun may occur.
| |
| | |
| Quick setup guide :
| |
| | |
| * Set inkscape to hpgl output
| |
| * draw figure and print to a file
| |
| * set serial port to 9600 8n1, crtscts.
| |
| * connect blue cable (a 9-pin gender-changer is needed at the PC end)
| |
| * load vinyl, switch cutter on. cutter should park at right hand side
| |
| * press Setup, cutter parks at left. Move cutter if necessary with cursor buttons, press Origin Set to mark lower right corner of drawing
| |
| * cat the inkscape output file to the serial port
| |
| | |
| It should be possible to enable the serial port as a printer and print direct to it, but I found this produced cutter errors (flashing power light) and no cut.
| |
| | |
| The following file was generated by inkskape for a star shape. This almost works : the first leg is replaced by a poorly cut arc. May imply a need for some sort of initialisation data.
| |
| | |
| IN;SP1;PU3999,6429;PD2693,5186;PD929,5557;PD1707,3932;PD809,2369;PD2596,2
| |
| 606;PD3805,1269;PD4131,3042;PD5776,3778;PD4191,4636;PD3999,6429;PD3999,6429;
| |
|
| |
|
| ==Pledges== | | ==Pledges== |
| * £20 --[[User:Artag|Artag]] 12:03, 4 August 2010 (UTC) | | * £30 --[[User:Velyks|Velyks]] |
| * £10 --[[User:Solexious|Solexious]]
| | * £10 --[[User:Detonate|Det]] |
| * £10 -- [[User:Jonty|Jonty]] | |
|
| |
|
| Running total: '''£40''' | | Running total: '''£40''' |
|
| |
|
| Approximate target: '''£???''' | | Approximate target: '''£78''' |
| | |
| | Paid: '''£0''' |
|
| |
|
| Total paid-up: '''£0'''
| | [[Category:Pledges]] |
