|
|
| (7 intermediate revisions by 4 users not shown) |
| Line 1: |
Line 1: |
| If you found some sweet settings please share them here.
| | ==Parameters for the new laser cutter== |
| ==Background== | |
| ===Thick Material===
| |
| Do not try to cut anything thicker than the thickest width listed for that material on this page.
| |
| ===Corner Power===
| |
| When the path goes round curves, or a straight line passes close to previous line (TBC), the laser will slow down. As a consequence, the Corner Power needs to be lower to compensate. Typically about 80% of the Power setting.
| |
| ===Lowest power===
| |
| Setting the power below 10 or 11 means that the laser will not activate.
| |
| ===Tried but DIY parameters===
| |
| Laser rubber has been used (mainly for stamps) it works well but you'll need to experiment for engraving/cutting
| |
|
| |
|
| ==Parameters==
| | Settings for the new [[Silvertail A0 Laser Cutter]] are available on the [[Silvertail A0 Laser Cutter/Cutting Parameters| Cutting Parameters page]]. |
| ===Cutting===
| |
| ====Acrylic - Perspex====
| |
| {| border="1"
| |
| !|Thickness (mm)
| |
| !|Speed (mm/sec)
| |
| !|Power (%)
| |
| !|Corner power (%)
| |
| !|Examples / Notes
| |
| |-
| |
| |3
| |
| |6
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |4
| |
| |3.5
| |
| |100
| |
| |21
| |
| |
| |
| |-
| |
| |5
| |
| |3
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |10
| |
| |1 (not enough?)
| |
| |100
| |
| |
| |
| |
| |
| |}
| |
|
| |
|
| ====PLY====
| | Settings for the old laser cutter which used to live here have now been moved to the [[Equipment/HPC LS3060 Laser Cutter|old Laser Cutter]] page for reference. '''Do not''' use these settings with the new cutter without some thought and careful adjustment since the new laser cutter is more powerful! |
| {| border="1"
| |
| !|Thickness (mm)
| |
| !|Speed (mm/sec)
| |
| !|Power (%)
| |
| !|Corner power (%)
| |
| !|Examples / Notes
| |
| |-
| |
| |.5
| |
| |25
| |
| |80
| |
| |
| |
| | This seemed to work really well with not much burn on the edges for the super thin ply.
| |
| |-
| |
| |1.5
| |
| |8
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |3
| |
| |5
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |5
| |
| |2
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |6
| |
| |1
| |
| |100
| |
| |
| |
| |
| |
| |}
| |
| | |
| ====MDF====
| |
| {| border="1"
| |
| !|Thickness (mm)
| |
| !|Speed (mm/sec)
| |
| !|Power (%)
| |
| !|Corner power (%)
| |
| !|Examples / Notes
| |
| |-
| |
| |3
| |
| |5
| |
| |100
| |
| |20
| |
| |
| |
| |-
| |
| |4
| |
| |4
| |
| |100
| |
| |
| |
| |
| |
| |}
| |
| | |
| ====Misc====
| |
| {| border="1"
| |
| !|Material
| |
| !|Thickness (mm)
| |
| !|Speed (mm/sec)
| |
| !|Power (%)
| |
| !|Corner power (%)
| |
| !|Examples / Notes
| |
| |-
| |
| |Acrylic - Palglas
| |
| |3
| |
| |6
| |
| |100
| |
| |21
| |
| |[[:File:Teabot-Cubauble.jpg|Cubauble]]
| |
| |-
| |
| |Corrugated Cardboard
| |
| |3
| |
| |12
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |Hardboard
| |
| |3
| |
| |3
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |Paper
| |
| |
| |
| |60
| |
| |15
| |
| |
| |
| |
| |
| |-
| |
| |Card
| |
| |
| |
| |35
| |
| |40
| |
| |
| |
| |
| |
| |-
| |
| |Mountboard
| |
| |
| |
| |12
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |Engraving Laminate
| |
| |
| |
| |15
| |
| |80
| |
| |
| |
| |
| |
| |-
| |
| |Funky Foam
| |
| |
| |
| |25
| |
| |25
| |
| |
| |
| |
| |
| |-
| |
| |Curian
| |
| |
| |
| |1
| |
| |100
| |
| |
| |
| |Four passes required
| |
| |-
| |
| |Laser Rubber
| |
| |
| |
| |6
| |
| |100
| |
| |25
| |
| |
| |
| |-
| |
| |Suede
| |
| |1
| |
| |25
| |
| |100
| |
| |25
| |
| |
| |
| |-
| |
| |Suede/Leather (line engraving)
| |
| |>1
| |
| |150
| |
| |10
| |
| |10
| |
| |
| |
| |-
| |
| |Leather
| |
| |3
| |
| |4
| |
| |100
| |
| |100 (needs more testing)
| |
| |
| |
| |-
| |
| |Full grain leather
| |
| |3
| |
| |9
| |
| |85
| |
| |85
| |
| |
| |
| |-
| |
| |LD45 Plastazote
| |
| |12
| |
| |25
| |
| |100
| |
| |20
| |
| |
| |
| |-
| |
| |[http://www.rapidonline.com/Tools-Fasteners-Production-Equipment/Enclosures/ABS-Boxes/ABS-Boxes-with-transparent-lids/62566 Unknown clear thermoplastic]
| |
| |4
| |
| |10
| |
| |10 - 15
| |
| |10
| |
| |These box lids melt easily but can be cut with multiple passes at low power.
| |
| |-
| |
| |Polypropylene sheet
| |
| |500micron (0,5mm)
| |
| |14
| |
| |40
| |
| |17
| |
| |
| |
| |-
| |
| |Polypropylene sheet - scoring
| |
| |500micron (0,5mm)
| |
| |60
| |
| |60
| |
| |15
| |
| | This will produce a score. useful if you want just to mark a point or fold.
| |
| |
| |
| |-
| |
| | Polyester "paper" - NeverTear
| |
| |300micron (0.3mm)
| |
| |40
| |
| |60
| |
| |40
| |
| | Never tear is a polyester sheet that can be laser printed like normal paper.
| |
| |
| |
| |-
| |
| | Polyester "paper" - NeverTear - Scoring
| |
| |300micron (0.3mm)
| |
| |100
| |
| |15
| |
| |40
| |
| | This will produce a score. useful if you want just to mark a point or fold.
| |
| |}
| |
| | |
| ===Engraving===
| |
| {| border="1"
| |
| !|Material
| |
| !|Speed (mm/sec)
| |
| !|Power (%)
| |
| !|Corner power (%)
| |
| !|Examples
| |
| |-
| |
| |Acrylic - Perspex
| |
| |200
| |
| |21
| |
| |
| |
| |
| |
| |-
| |
| |Birch PLY
| |
| |200
| |
| |17
| |
| |
| |
| |
| |
| |-
| |
| |MDF
| |
| |200
| |
| |25
| |
| |
| |
| |
| |
| |-
| |
| |Corrugated Cardboard
| |
| |200
| |
| |20
| |
| |
| |
| |
| |
| |-
| |
| |Hardboard
| |
| |200
| |
| |20
| |
| |
| |
| |
| |
| |-
| |
| |Paper
| |
| |200
| |
| |15
| |
| |
| |
| |
| |
| |-
| |
| |Card
| |
| |300
| |
| |20
| |
| |
| |
| |
| |
| |-
| |
| |Mountboard
| |
| |200
| |
| |20
| |
| |
| |
| |
| |
| |-
| |
| |Engraving Laminate
| |
| |200
| |
| |21
| |
| |
| |
| |
| |
| |-
| |
| |Curian
| |
| |3
| |
| |100
| |
| |
| |
| |
| |
| |-
| |
| |Laser Rubber | |
| |200
| |
| |70
| |
| |
| |
| |
| |
| |-
| |
| |Anodized aluminium (dyed black)
| |
| |450
| |
| |90
| |
| |?
| |
| |[http://www.flickr.com/photos/russss/4991794474/ LHS logo on black phone]
| |
| |-
| |
| |Anodized aluminium (Macbook Pro) (Vector - in "cut" mode)
| |
| |100
| |
| |100
| |
| |80
| |
| |[http://www.flickr.com/photos/russss/5091497832/ Russ's Macbook Pro]
| |
| |-
| |
| |Suede
| |
| |250
| |
| |15
| |
| |80
| |
| |
| |
| |-
| |
| |LD45 Plastazote
| |
| |200
| |
| |10
| |
| |10
| |
| |At 10% engraves 2-3mm deep. Laser doesn't seem to come on at all at 5% or engrave at speeds >200 mm/s so may not be possible to engrave less deeply than this.
| |
| |-
| |
| |}
| |
