Difference between revisions of "Project:Plant species testing"

From London Hackspace Wiki
Jump to navigation Jump to search
Line 5: Line 5:
 
Extraction (From [http://www.springerlink.com/content/n6293v8808n5g836/ this] paper - we also have full text available):
 
Extraction (From [http://www.springerlink.com/content/n6293v8808n5g836/ this] paper - we also have full text available):
  
* 'Homogenize' (mush) approx 40 mg pea with a pestle in 300ug of 5% chelex solution for 1 min   
+
* 'Homogenize' (mush) approx 40 mg pea with a pestle in 300ul of 5% chelex solution for 1 min   
 
* Vortex for 10s then boil for 5 mins, then vortex again for 10s. (Hot plate lost heat in the middle so we boiled for 8 mins)  
 
* Vortex for 10s then boil for 5 mins, then vortex again for 10s. (Hot plate lost heat in the middle so we boiled for 8 mins)  
 
* Centrifuge for 1 min - recover supernatant and use as template
 
* Centrifuge for 1 min - recover supernatant and use as template

Revision as of 09:33, 20 July 2012

We are using primers for plants to test and refine our DNA extraction / PCR technique. First project is to test for peas. Inspiration and primers are in this paper. We are using two methods of extraction. 1st attempt with a chelex protocol, 2nd with alcohol precipitation.

1st go - 17 and 18/7/12

Extraction (From this paper - we also have full text available):

  • 'Homogenize' (mush) approx 40 mg pea with a pestle in 300ul of 5% chelex solution for 1 min
  • Vortex for 10s then boil for 5 mins, then vortex again for 10s. (Hot plate lost heat in the middle so we boiled for 8 mins)
  • Centrifuge for 1 min - recover supernatant and use as template

PCR:

  • Prepare sample with 12.5 ul of Taq ready mix, 2 ul of each primer, 3 ul of template, and 5.5 ul of distilled water.
  • Denature at 96°C for 5 mins
  • 40 cycles of D = 96°C for one minute, A = 58°C for 30 seconds, E = 72°C for one minute.
  • Put paraffin on top after 5 mins (should have been before start)

Electrophoresis:

  • 100ml of agarose solution: 1 gram of agarose powder added to 100ml of 1% TBE solution
  • Microwaved the agarose, cooled to 50 degrees, added 5ul of ethidium bromide stock solution
  • Poured agarose into mould and waited to cool, then covered with 1% TBE.
  • Put ladder into far well, template into near well
  • Electrophoresed for 1 hr - started at 80V, settled at around 130V
  • Visualised under UV light through orange filter - did not see any bands from the template, but ladder was visible, indicating PCR failed.

2nd go

  • Blend peas with salt and detergent according to this protocol. Sieve.
  • Incubate for 15 mins at 60°C (optional step that we didn't take)
  • Centrifuge - recover supernatant
  • Add proteinease K (100 ul of 1mg / ml solution to 300 ul of pea template) - incubate for 1 hr at 50C (action of proteinase k) then 94 C for 10 mins (inactivation of proteinase K)
  • Precipitation to follow