Difference between revisions of "Laser Cutter/Metal"
m (CDave moved page London Hackspace Wiki:Laser Cutter/Metal to Laser Cutter/Metal) |
(Changed page to be about Metal in general, not just laptops & added Akki's laptop) |
||
| Line 1: | Line 1: | ||
| + | * '''You can't cut metal in the laser cutter''': if you wish to mark the metal, please use Thermark / Cermark, or use anodised aluminium. | ||
| − | == | + | == Anodised Aluminium == |
| + | TODO: add somthing about laser ablation. | ||
| − | Simon | + | == Laser Bonding == |
| + | |||
| + | An alternative to removing a layer of anodised material, is the [http://en.wikipedia.org/wiki/Laser_bonding bond a layer] of new material onto the metal, e.g. Cermark, or [http://www.evilmadscientist.com/2013/laser-moly/ cheap moly lube]. | ||
| + | |||
| + | ==Hackspace Experiences== | ||
| + | === Dell 2013-02-28 === | ||
| + | |||
| + | Akki did a "cut" line design (as opposed to etching which is filled in) on [http://www.flickr.com/photos/fishies_go_pook/8516279713/ a black Dell laptop] and it was done in less than 30 seconds. | ||
| + | |||
| + | === MacBook Air 2013-08-07 === | ||
| + | |||
| + | Simon etched the back of his macbook air using the Engraving setting. | ||
Speed was 200, Power was 80. | Speed was 200, Power was 80. | ||
| Line 13: | Line 26: | ||
[https://plus.google.com/104824939898236764564/posts/YPNd1m6WnbK] | [https://plus.google.com/104824939898236764564/posts/YPNd1m6WnbK] | ||
| − | + | === MacBook Air 2014-03-08 === | |
| − | == 2014-03-08 == | ||
Patrick engraved the front of a MacBook-pro | Patrick engraved the front of a MacBook-pro | ||
| Line 21: | Line 33: | ||
Maybe the anodised aluminium has changed in recent years? | Maybe the anodised aluminium has changed in recent years? | ||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 12:11, 12 March 2014
- You can't cut metal in the laser cutter: if you wish to mark the metal, please use Thermark / Cermark, or use anodised aluminium.
Anodised Aluminium
TODO: add somthing about laser ablation.
Laser Bonding
An alternative to removing a layer of anodised material, is the bond a layer of new material onto the metal, e.g. Cermark, or cheap moly lube.
Hackspace Experiences
Dell 2013-02-28
Akki did a "cut" line design (as opposed to etching which is filled in) on a black Dell laptop and it was done in less than 30 seconds.
MacBook Air 2013-08-07
Simon etched the back of his macbook air using the Engraving setting.
Speed was 200, Power was 80.
The effect looks good in bright light (when it looks black) The 'whiteness' of the etching is inconsistent, looking dirty/smokey in areas where it was denser. I'm guessing maybe some of the smoke? got annodized into the metal? Anyway it was on the back and just a test.
A couple of pictures are up at [1]
Planning on what to do to the front. [2]
MacBook Air 2014-03-08
Patrick engraved the front of a MacBook-pro
Speed was sloooow, power was 100, and the design was barely visible after over an hour of lasing time.
Maybe the anodised aluminium has changed in recent years?