Difference between revisions of "Laser Cutter/Parameters"

From London Hackspace Wiki
Jump to navigation Jump to search
(Removed parameters to the old laser cutter page for reference to prevent accidental use of old settings in new laser cutter (like I just did!))
 
(4 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
If you found some sweet settings please share them here.
+
==Parameters for the new laser cutter==
−
==Background==
 
−
===Thick Material===
 
−
Do not try to cut anything thicker than the thickest width listed for that material on this page.
 
−
===Corner Power===
 
−
When the path goes round curves, or a straight line passes close to previous line (TBC), the laser will slow down. As a consequence, the Corner Power needs to be lower to compensate. Typically about 80% of the Power setting.
 
−
===Lowest power===
 
−
Setting the power below 10 or 11 means that the laser will not activate.
 
−
===Tried but DIY parameters===
 
−
Laser rubber has been used (mainly for stamps) it works well but you'll need to experiment for engraving/cutting.  Check out [[Laser_Cutter/Parameters#GradeEngrave]], which is useful for rubber stamps.
 
  
−
==Parameters==
+
Settings for the new [[Silvertail A0 Laser Cutter]] are available on the [[Silvertail A0 Laser Cutter/Cutting Parameters| Cutting Parameters page]].
−
===Cutting===
 
−
====Acrylic - Perspex====
 
−
{| border="1"
 
−
!|Thickness (mm)
 
−
!|Speed (mm/sec)
 
−
!|Power (%)
 
−
!|Corner power (%)
 
−
!|Examples / Notes
 
−
|-
 
−
|3
 
−
|6
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|4
 
−
|3.5
 
−
|100
 
−
|21
 
−
|
 
−
|-
 
−
|5
 
−
|3
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|10
 
−
|1 (not enough?)
 
−
|100
 
−
|
 
−
|
 
−
|}
 
  
−
====PLY====
+
Settings for the old laser cutter which used to live here have now been moved to the [[Equipment/HPC LS3060 Laser Cutter|old Laser Cutter]] page for reference. '''Do not''' use these settings with the new cutter without some thought and careful adjustment since the new laser cutter is more powerful!
−
{| border="1"
 
−
!|Thickness (mm)
 
−
!|Speed (mm/sec)
 
−
!|Power (%)
 
−
!|Corner power (%)
 
−
!|Examples / Notes
 
−
|-
 
−
|.5
 
−
|25
 
−
|80
 
−
|
 
−
| This seemed to work really well with not much burn on the edges for the super thin ply.
 
−
|-
 
−
|1.5
 
−
|8
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|3
 
−
|5
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|5
 
−
|2
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|6
 
−
|1
 
−
|100
 
−
|
 
−
|
 
−
|}
 
−
 
 
−
====MDF====
 
−
{| border="1"
 
−
!|Thickness (mm)
 
−
!|Speed (mm/sec)
 
−
!|Power (%)
 
−
!|Corner power (%)
 
−
!|Examples / Notes
 
−
|-
 
−
|3
 
−
|5
 
−
|100
 
−
|20
 
−
|
 
−
|-
 
−
|4
 
−
|4
 
−
|100
 
−
|
 
−
|
 
−
|}
 
−
 
 
−
====Misc====
 
−
{| border="1"
 
−
!|Material
 
−
!|Thickness (mm)
 
−
!|Speed (mm/sec)
 
−
!|Power (%)
 
−
!|Corner power (%)
 
−
!|Examples / Notes
 
−
|-
 
−
|Acrylic - Palglas
 
−
|3
 
−
|6
 
−
|100
 
−
|21
 
−
|[[:File:Teabot-Cubauble.jpg|Cubauble]]
 
−
|-
 
−
|Corrugated Cardboard
 
−
|3
 
−
|12
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|Hardboard
 
−
|3
 
−
|3
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|Paper
 
−
|
 
−
|60
 
−
|15
 
−
|
 
−
|
 
−
|-
 
−
|Card
 
−
|
 
−
|35
 
−
|40
 
−
|
 
−
|
 
−
|-
 
−
|Mountboard
 
−
|
 
−
|12
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|Engraving Laminate
 
−
|
 
−
|15
 
−
|80
 
−
|
 
−
|
 
−
|-
 
−
|Funky Foam
 
−
|
 
−
|25
 
−
|25
 
−
|
 
−
|
 
−
|-
 
−
|Curian
 
−
|
 
−
|1
 
−
|100
 
−
|
 
−
|Four passes required
 
−
|-
 
−
|Laser Rubber
 
−
|
 
−
|6
 
−
|100
 
−
|25
 
−
|
 
−
|-
 
−
|Suede
 
−
|1
 
−
|25
 
−
|100
 
−
|25
 
−
|
 
−
|-
 
−
|Suede/Leather (line engraving)
 
−
|>1
 
−
|150
 
−
|10
 
−
|10
 
−
|
 
−
|-
 
−
|Leather
 
−
|3
 
−
|4
 
−
|100
 
−
|100 (needs more testing)
 
−
|
 
−
|-
 
−
|Full grain leather
 
−
|3
 
−
|9
 
−
|85
 
−
|85
 
−
|Burn free result! Helps to put tape over leather.
 
−
|-
 
−
|LD45 Plastazote
 
−
|12
 
−
|25
 
−
|100
 
−
|20
 
−
|
 
−
|-
 
−
|[http://www.rapidonline.com/Tools-Fasteners-Production-Equipment/Enclosures/ABS-Boxes/ABS-Boxes-with-transparent-lids/62566 Unknown clear thermoplastic]
 
−
|4
 
−
|10
 
−
|10 - 15
 
−
|10
 
−
|These box lids melt easily but can be cut with multiple passes at low power.
 
−
|-
 
−
|Polypropylene sheet
 
−
|500micron (0,5mm)
 
−
|14
 
−
|40
 
−
|17
 
−
|
 
−
|-
 
−
|Polypropylene sheet - scoring
 
−
|500micron (0,5mm)
 
−
|60
 
−
|60
 
−
|15
 
−
| This will produce a score. useful if you want just to mark a point or fold.
 
−
|
 
−
|-
 
−
| Polyester "paper" - NeverTear
 
−
|300micron (0.3mm)
 
−
|40
 
−
|60
 
−
|40
 
−
| Never tear is a polyester sheet that can be laser printed like normal paper.
 
−
|
 
−
|-
 
−
| Polyester "paper" - NeverTear - Scoring
 
−
|300micron (0.3mm)
 
−
|100
 
−
|15
 
−
|40
 
−
| This will produce a score. useful if you want just to mark a point or fold.
 
−
|}
 
−
 
 
−
===Engraving===
 
−
{| border="1"
 
−
!|Material
 
−
!|Speed (mm/sec)
 
−
!|Power (%)
 
−
!|Corner power (%)
 
−
!|Examples
 
−
|-
 
−
|Acrylic - Perspex
 
−
|200
 
−
|21
 
−
|
 
−
|
 
−
|-
 
−
|Birch PLY
 
−
|200
 
−
|17
 
−
|
 
−
|
 
−
|-
 
−
|MDF
 
−
|200
 
−
|25
 
−
|
 
−
|
 
−
|-
 
−
|Corrugated Cardboard
 
−
|200
 
−
|20
 
−
|
 
−
|
 
−
|-
 
−
|Hardboard
 
−
|200
 
−
|20
 
−
|
 
−
|
 
−
|-
 
−
|Paper
 
−
|200
 
−
|15
 
−
|
 
−
|
 
−
|-
 
−
|Card
 
−
|300
 
−
|20
 
−
|
 
−
|
 
−
|-
 
−
|Mountboard
 
−
|200
 
−
|20
 
−
|
 
−
|
 
−
|-
 
−
|Engraving Laminate
 
−
|200
 
−
|21
 
−
|
 
−
|
 
−
|-
 
−
|Curian
 
−
|3
 
−
|100
 
−
|
 
−
|
 
−
|-
 
−
|Laser Rubber
 
−
|200
 
−
|70
 
−
|
 
−
|
 
−
|-
 
−
|Anodized aluminium (dyed black)
 
−
|450
 
−
|90
 
−
|?
 
−
|[http://www.flickr.com/photos/russss/4991794474/ LHS logo on black phone]
 
−
|-
 
−
|Anodized aluminium (Macbook Pro) (Vector - in "cut" mode)
 
−
|100
 
−
|100
 
−
|80
 
−
|[http://www.flickr.com/photos/russss/5091497832/ Russ's Macbook Pro]
 
−
|-
 
−
|Suede
 
−
|250
 
−
|15
 
−
|80
 
−
|
 
−
|-
 
−
|LD45 Plastazote
 
−
|200
 
−
|10
 
−
|10
 
−
|At 10% engraves 2-3mm deep. Laser doesn't seem to come on at all at 5% or engrave at speeds >200 mm/s so may not be possible to engrave less deeply than this.
 
−
|-
 
−
|}
 
−
 
 
−
== GradeEngrave ==
 
−
 
 
−
Grade Engrave will cause an area inside a engraved area to have raised edges. It is intended for easier rubber stamp making but can be applied to any real use. See the [https://wiki.nottinghack.org.uk/wiki/Laser_cutter/LaserCut/Usage#Grade_Engrave Nottinghack wiki] for more details. 
 
−
 
 
−
It ramps the power slightly as it comes out of an engraving groove, so you get little ridges around the edge of your engraving. 
 
−
 
 
−
 
 
−
[[File:GradeEngrave-stamp.jpg|thumb|What happens when you use GradeEngrave]]
 
−
 
 
−
 
 
−
{| border="1"
 
−
!|Material
 
−
!|Speed (mm/sec)
 
−
!|Power (%)
 
−
!|Corner power (%)
 
−
!|Examples
 
−
|-
 
−
|Laser Rubber
 
−
|200
 
−
|70
 
−
|
 
−
| Two passes might work better :)
 
−
}
 
−
|-
 

Latest revision as of 14:57, 25 June 2015

Parameters for the new laser cutter

Settings for the new Silvertail A0 Laser Cutter are available on the Cutting Parameters page.

Settings for the old laser cutter which used to live here have now been moved to the old Laser Cutter page for reference. Do not use these settings with the new cutter without some thought and careful adjustment since the new laser cutter is more powerful!

Retrieved from ‘https://wiki.london.hackspace.org.uk/w/index.php?title=Laser_Cutter/Parameters&oldid=47367’