Difference between revisions of "Pledge: Vinyl"
| Line 9: | Line 9: | ||
The cutter is being donated by Tomwardill, with a small stock of vinyl. However, we will need more and Tom would appreciate donations towards the cost of his larger stocks. Please indicate if you can help. | The cutter is being donated by Tomwardill, with a small stock of vinyl. However, we will need more and Tom would appreciate donations towards the cost of his larger stocks. Please indicate if you can help. | ||
| + | |||
| + | ==Operation== | ||
| + | |||
| + | I have had a certain amount of success running the cutter with a serial connection from Inkscape under Linux. More messing around is needed.--[[User:Artag|Artag]] 13:32, 19 August 2010 (UTC) | ||
| + | |||
| + | * Sometimes the cutter refuses to print or respond to any buttons. This hasn't happened since I opened a door in the bottom of the printer and poked an EPROM there, so may be due to some poor internal connection. | ||
| + | |||
| + | * The serial cable (blue, with a 25WD at one end and a 9WD at the other) is connected as follows : | ||
| + | |||
| + | {|border="1" cellpadding="5" cellspacing="0" | ||
| + | |- | ||
| + | |Cutter, 25 pin male D ||PC, 9 pin female D||Use | ||
| + | |- | ||
| + | |pin 2 || pin 2 || PC RXD from cutter | ||
| + | |- | ||
| + | | 3 || 3 || PC TXD to cutter | ||
| + | |- | ||
| + | | 4 || n/c || cutter pin 5, RTS CTS loopback | ||
| + | |- | ||
| + | | 5 || n/c || cutter pin 4, RTS CTS loopback | ||
| + | |- | ||
| + | | 7 || 5 || ground | ||
| + | |- | ||
| + | | 20 || 8 || cutter DTR to PC CTS, flowcontrol | ||
| + | |} | ||
| + | |||
| + | This provides for hardware (rts/cts) handshake. Software flowcontrol may be OK but the cutter manual suggests overrun may occur. | ||
| + | |||
| + | |||
==Pledges== | ==Pledges== | ||
Revision as of 13:32, 19 August 2010
.jpg)
Model is a Roland CAMM-1 PNC-950. It hold up to 610mm (24") media and cuts up to 584mm ( ~23"). Length is essentially unlimited as it can use roll-feed media but seems to be restricted to 25m.
Manual: http://www.signcutpro.com/files/man/roland/pnc950.pdf
The cutter is being donated by Tomwardill, with a small stock of vinyl. However, we will need more and Tom would appreciate donations towards the cost of his larger stocks. Please indicate if you can help.
Operation
I have had a certain amount of success running the cutter with a serial connection from Inkscape under Linux. More messing around is needed.--Artag 13:32, 19 August 2010 (UTC)
- Sometimes the cutter refuses to print or respond to any buttons. This hasn't happened since I opened a door in the bottom of the printer and poked an EPROM there, so may be due to some poor internal connection.
- The serial cable (blue, with a 25WD at one end and a 9WD at the other) is connected as follows :
| Cutter, 25 pin male D | PC, 9 pin female D | Use |
| pin 2 | pin 2 | PC RXD from cutter |
| 3 | 3 | PC TXD to cutter |
| 4 | n/c | cutter pin 5, RTS CTS loopback |
| 5 | n/c | cutter pin 4, RTS CTS loopback |
| 7 | 5 | ground |
| 20 | 8 | cutter DTR to PC CTS, flowcontrol |
This provides for hardware (rts/cts) handshake. Software flowcontrol may be OK but the cutter manual suggests overrun may occur.
Pledges
Running total: £40
Approximate target: £???
Total paid-up: £0