Equipment/Stratasys FDM 1650/Legacy
This sub-page is to serve as an archive for the old logs and data about the Stratasys before it's extensive refurbishment.
Training & instruction
If you haven't used it before, please contact Chris Paton / Hipster and get him to show you how it works.
Answers from Stratasys to emails:
We stop supporting this system a couple years ago, so getting the software for this system is not possible because it cannot be purchased and is only available through a maintenance contract. We are not aware of any third party or open source application that would work on this system.Quickslice might be archived somewhere, however, we have to adhere to company policy.
Insight is Stratasys' program that lets you import stl files. There are minimal file manipulation tools, but it does let you reorient the model and scale it. An inputted stl file is then used to create a series of horizontal cross sections at a set Z interval. For modeling with ABS, this interval is 0.010".
Models are built out of a "build" or "model" material, but to support higher layers of this model material, a "support" material is typically laid down first. After creating support material, there toolpaths must be generated for the support and build extruding heads to follow as they create the part. These toolpaths are also called "roads."
For beginning modelers, Insight should be used to reorient the model (to decrease build time), to scale the model, to generate the slices (slc) and toolpaths (sml) files, and to give the operator information about the build time and material requirements. Fortunately, much of this can be done automatically.
6. In Insight, click "File," "Open," and browse to find your stl file to load; it is probably not on the default C:\ drive. If a dialog box reports that the part is oversized, ignore it; you can re-scale the part within Insight.
7. On the right of the screen the "Modeler Setup" box will indicate the configuration. For typical operation with ABS plastic, this should indicate
FDM 1650 - 0.0100 slice height.
Model T12 tip ABS P400 Support T12 tip ABS P400R
Part fill style
Part interior style
10. Reorient your model so that the support material required and the and build time are minimized. There are some applications where part finish or other factors affect orientation decisions. To reorient the model, click "STL", "Rotate." Use the dialog boxes at the right to specify the rotation amount and direction. Repeat, as necessary. Even though your model might appear on the screen in the front, left of the build platform, you will be able to relocate it to any other suitable location after it is sent to the FDM, and the model should not be moved at this time, except to facilitate multiple model loading. (There is also an Automatic Orientation feature you may wish to use to, say, minimize supports.)
11. Scale your model, if appropriate. FDM material is very expensive, and large models take a very long time to build. Select "STL," "Units and Scale." You may use the values in the pull down window beside "STL scale," or type in your own factor. You may not notice a change in your object, but the size of the surrounding box might seem to change. The build envelope is a 10" cube, and the box on the screen around your object represents this envelope. Note the "STL size" readout in the "STL Units and Scale" dialog box. 12. Slice your virtual model by selecting the "Slice" icon.
13. Generate supports by selecting the "Support" icon
14. Create toolpaths by selecting the "Toolpaths" icon.
15. It's a good idea to then click "File, Save" to save your toolpaths file
16. Back at the FDM, check to see if there is enough space on the foam build platform for your model. If there is not enough room, replace the foam.
If it is necessary to replace the foam:
A. Open the FDM front door. Watch where you put your hands; avoid getting burnt.
B. Flip the locking lever on the front, left of the build platform.
C. Pull the build platform forward, removing it from the FDM.
D. Close the FDM door.
E. Place the build platform on a table, and remove all 10 pins and the foam insert.
F. Remove any foreign materials from the build platform.
G. Flip the foam over, or if the underneath face was already used, select a new piece of foam. Note that the brown urethane foam is designed for ABS and the blue polystyrene foam is designed for investment casting wax (ICW).
H. Place the foam into the platform so it is seated firmly. This might require shearing part of the edge of the foam.
I. Invert the build platform so the foam is against a table.
J. Pressing down firmly on the platform, replace all 10 pins.
K. Blow off any debris, and replace the build platform in the FDM, securing the locking lever and closing the door.
17. Check to see of the three temperature readings are sufficient.
18. Check the Auto Shut Off status, and change it appropriately by depressing the Auto SO key on the FDM. If you will be the last to build a model for the day, turn Auto SO on; if another model will be built right after yours, leave it off.
19. Extrude a bit of plastic from each head, to make sure there is no problem. To do this, toggle the Model/Support button until it the display reads Model. Then press the Load button once. In five to ten seconds you should see a strand exiting the model head. Press the Load button again to cancel the load. (Whatever you do, do not press the Unload button, as this backs the material out of the head.) Then press Model/Support to toggle to the support material and repeat. If plastic was extruded from both heads, then all you need do is brush off the plastic from the heads, and make sure the platform and rear brass brush are clear of debris. If one of the heads did not extrude plastic, or if there was an error message, please let the lab supervisor know.
20. Notice the button on near the top, center of the FDM that says "Prgm 0" above it and "Pause" below it. Let's call this the Pause Button. If this button has a flashing amber light, press that button now to turn off the light. If the light is on, the FDM cannot receive information from the computer.
21. Back in Insight, click the "Build" icon. In the "Pack and Download" dialog box, copy the following information to your notes:
* Estimated Model Material to be used: * Estimated Support Material to be used * Total time estimate:
Also, make a note of the present date and time and of the date and time when the job should finish. Click the icon to send the job to the modeler. (If you had wanted to send multiple copies to the FDM to be built simultaneously, you would have indicated so in this dialog box.)
22. The Pause Button light should be flashing; press it to turn it off. This will cause the FDM to run through initialization routines, extruding support material and wiping the tips. When it is done, the light will come on again.
23. Use the directional keys on the FDM to move the head in the XY plane, or the platform in the Z axis. Pressing the center key along with another key invokes a faster mode. There is also a toggle button so that the up/down keys can be control both the Y and Z axes. If necessary, lower the platform, open the door, and use the brass brush to gently clean the extruding tips. Be sure to also remove excess material from the inverted brush in the machine and from other areas in the machine and close the door. Reposition the left "build material" tip so that it is at the front, left of the rectangle where you wish the build to occur. Try to get the tip so it is barely touching the foam, neither embedded in it, nor above it.
24. Press the Pause Button light.
25. Note the time, the amount of material required, and estimate the approximate time of completion.
26. Turn off the monitor. Since an active serial cable connection is required for the build to continue, other applications on that computer might interfere with the build. It is a good idea, therefore, to avoid using the computer for anything else during building.
27. Return when the model is almost finished, or if its an overnight build, then return as soon as the lab opens in the morning. Put on your safety glasses again.
28. Make sure your files are stored in the appropriate place for your class.
29. When the model is done building, the head will go to the home position, the Pause Button light will flash, and the FDM display will show "100%". Open the door and gently remove your model. You might wish to remove the build platform to make this easier (especially for large models), but replace the platform when you are done. A fingernail may be used to remove the model from the foam. Close the door.
30. Move any files created to the appropriate directory; do not merely copy them.
31. If no other user is about to build a model, log off of the computer, and turn off the computer, the monitor, and the FDM. The fan in the FDM will probably still operate for a while.
32. Carefully remove the support material from your model so you do not injure yourself or the model. Recommended tools for this are needle nose pliers, tweezers, and maybe a small screwdriver, and an X-Acto knife. If necessary, sand the model very lightly. Clean the FDM and, if necessary, finish your model. Be careful to avoid cutting yourself, to avoid breaking the model or a knife, and to protect your eyes from flying debris. Make sure others around you have eye protection. Please place all trash into the trash receptacle.
- Serial to parallel adapter from server
- parallel cable into back of FDM
- FDM power on (white button on front that says start)
- Server on
- Launch insight application
(It's probably not a parallel cable, just a 25pin RS232 port).
Bits per second : 9600
Data Bits : 7
Parity : None
Stop Bits : 1
Flow Control : Xon/Xoff
These settings are stored in a Hyperterminal session called FDM1650.
- If we wanted to use the stratasys with skeinforge, we'd need to get skeinforge to output appropriate movement commands or, perhaps more maintainably, translate the G-code output into ACL. This might not be too difficult : skeinforge seems to use a very limited section of G and M codes, notably
G1 linear move G2 cw arc G3 ccw arc G21 set units to mm G28 home G90 set absolute distance mode G91 set incremental distance mode M101 extruder on M103 extruder off M104-108 extruder temperature control M110 filament height ? M113 duty cycle ?
- Write translator to perform the above conversion
Firmware Version is 9.01 OF: Calibration factors: 1.0027,1.0028 OI: AUTOMOVE REV 3.60/3.60 OL: travel limits: 0,0, 12000, 12000 ON: digital inputs state: 0 OO: origin : 0,0 OP: Personality parameters: (enter OP<space>n; or OP<space>nn;) 1: Arrow Single Step Delay: 3000 (factory) 2: Arrow slow step delay: 100 (factory) 3: Arrow Fast Step Delay: 3 (factory) 4: X Arrow Direction Swap: 0 (factory) 5: 0 6: 0 7: 250 8: 2 9: 2 10: 100 11: 100 12: 100 13: 100 14: 32767 15: 32767 16: 32767 17: -15 18: -15 19: 1.0027 20: 1.0028 21: 8 22: 8 23: 0 24: 0 25: 12000 26: 12000 27: 16504 28: 16504 29: 1 30: 0 31: 1 32: 40 33: 10000 34: 40 35: 10000 36: 0 37: 0 38: 255 39: -1 40: 200 41: 25 42: 1 43: 0 44: 100 45: 32767 46: 0 47: 200 48: 0 49: 0 50: -1 51: 500 52: 0 53: 150 54: 400 55: 400 56: 10 57: 1 58: 0 59: 0 60: 0
Any or all of these issues need investigating - but not haphazardly
- Document everything you do the same day
- Not just solid new information - add any progress, concerns, ideas, speculation etc.
- Do NOT leave the stratasys in bits
- If you must leave something incomplete, put all the parts in a bag attached to the machine, document it here and put a note on the machine if it should not be switched on or is otherwise restricted.
- Do NOT leave parts strewn around the adjacent table after you finish work
- Tidy up, refit all covers, use as little space as possible. It's only tolerable to keep the machine out of the awkward alcove if it doesn't take over a whole load of extra space.
- Do not assume you'll come back to finish something the next day etc. even if that's your plan - always leave the machine as though someone else will be working on it next.
Current Status - 4/11/11
- Hipster got it working after striping the extruder assembly and cleaning the whole block.
01:20 < lovelace_> from hipster... I JUST GOT FDM TO DO ITS FIRST PRINT!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
new wiki entry: 
- After Samthetechie took a look earlier this week, Hipster Chris managed to get the software running
- Set the port to COM1, sent a bathplug model, and tried to print
- Needs some config to set the limits
- Still needs the powering-off bug to be fixed.
- Attempted to run windows software. but windows refuses to run as it isn't licensed.
- Taken CD home in the hope I can install it elsewhere
- Moved out of alcove and tried a few basic things.
- Self-test ran (aborted) after restoring front panel connector.
- All axes capable of movement using arrow pad.
- Remaining parameters dumped and entered in wiki
- Feed Home command works
- Z home using buttons appears not to stop (aborted, looked dangerous)
- ACL manual reports that microstepping is used (but is that for a different controller ?)
(Billy posted this to the mailing list)
Ally, one of Dean's friends, has said that she's happy to help us repair it. She's worked on older versions of the Stratasys printers, and she's already had a look at the electronics. She's happy to to show people what needs doing, and how to do it, though she'll need her expenses covering for travel. I think it's inside the M25.
I'll pass along the contact details.
As for the state of the Stratasys. The transport mechanisms work fine. Both extruders seem to work. The temperature control mechanisms seem to work, though the machine has the tendency to run for a while, then shut down instantly.
From what Ally said, this is usually due to either leaking capacitors, or two-legged transistors. Usually simple enough to replace, but this project went waaaaaaaay past my skill levels in electronics a long time ago... :))
The server sitting next to the Stratasys is set up with the OS and software needed. We can communicate with the control boards happily.
The rackmount machine on the floor is now running XP again; somebody, likely Billy, reinstalled the system without updating this page.
I've installed speedfan, and disconnected some of the non-software-controllable fans. This makes it somewhat less horribly loud.
I've also started documenting the initial parameters below.
The correct serial settings are 9600 7E1 (that is, even parity, 7 data bits, 1 stop bit). Other settings work, but ESC.E gives errors.
The rackmount machine on the floor under the terminal to the right of the stratasys is named capak (the man who coined the term "robot"). The user is hackspace/hackspace. Please use sudo for root. (The root password is also hackspace.)
If you know why the monitor is nigh-unreadable, please fix it.
It should be possible to ssh to it from within the space. (Use capak.local.)
It's kind of functional.
There's an computer connected to it and we can get a serial port connection on COM1.
At the moment it's only returning error messages.
The automated tools can connect happily.
IT STILL NEEDS CALIBRATION BEFORE USE!!!
Please do this first, and let us know what happened.
There are two printed manuals, a printed service manual, and the rest of the docs are on the desktop in the Stratasys folder.
I'm in the middle of setting up the software. It's NOT usable yet!
I'll be back later tonight to finish setting it up...
- Power up normally. Are there any bad-looking lights on the front panel? If so, something is stuck.
DONE! - It's fine.
- Power up with left and right buttons pressed, should start self-test run. It will loop, power-off or hit reset to stop it.
DONE! - It works as expected. Ran through all the self-tests, and they came out ok. They're all in the service manual. Have a look.
- Connect the serial port up. Document how to reach it on this wiki page.
- Open her up, document the position of the switches on the back of the automove unit.
- Determine serial parameters from the dip switches, see page 9 of the automove operation manual.
- Using the acl docs, find the current values of the personality parameters, document them here. This will hopefully keep us from losing them by accident later, and tell us a bit about how the machine is set up. You'll want the OP command, page 3-50, and the list of personality parameters, page 14-1.