Search results
From London Hackspace Wiki
Page title matches
- 33 bytes (3 words) - 00:34, 27 April 2014
Page text matches
- ...moving different parts of the sample into the focal plane. This is called z-stacking. ...to create a platform, using parts from a 3d printer, to automate creating z-stacked photomicrographs using a cheap ole' researcher microscope.838 bytes (135 words) - 10:13, 10 August 2014
- * Adjusted Z-axis now doing ~100mm when told to. * Wired Z-Axis and is moving1 KB (211 words) - 18:06, 31 May 2014
- * The most important new point to remember: '''Do not use the Z datum function with your material beneath the cutter head.''' There is a go [[File:Silvertail_Z_Adjustment.jpg|300px|thumbnail|right|Z height adjustment]]2 KB (380 words) - 19:36, 24 February 2020
- ...tware on the PC, choose a smallish step size and keep pressing the up/down z axis buttons. Little steps take it easy! ...to select, then choose the Z axis. Again, choose a small step size on the z axis.2 KB (276 words) - 10:52, 20 March 2020
- ...rds / away from you (+y is travelling away from you), and z is down / up (+z is travelling up) ...datum of the workpiece, for instance touching off the tool in x, y and z (z is very important)2 KB (380 words) - 19:19, 20 November 2017
- ...rds / away from you (+y is travelling away from you), and z is down / up (+z is travelling up) ...datum of the workpiece, for instance touching off the tool in x, y and z (z is very important)4 KB (651 words) - 18:54, 19 November 2017
- |model=Dahlgren Wizzard 2000 ST (heavily hacked) <!-- Model --> |location=Basement, Robotics/CNC area <!-- Floor, room/zone and location within that area -->5 KB (836 words) - 11:53, 21 January 2019
- ...rds / away from you (+y is travelling away from you), and z is down / up (+z is travelling up) ...datum of the workpiece, for instance touching off the tool in x, y and z (z is very important)4 KB (724 words) - 18:38, 19 November 2017
- * 10 11: start moving up (Z), must be followed by 0e * 10 12: start moving down (Z), must be followed by 0e3 KB (387 words) - 21:10, 8 July 2011
- <td> [http://www.thingiverse.com/thing:9622 Nophead's Z Coupling: ] </td> <td>z-motor-mount</td>9 KB (1,585 words) - 12:42, 16 May 2013
- * Z axis works ...ced a gcode file which did print, admittedly with a bit of elephants foot, Z axis offset needed some adjustment.2 KB (373 words) - 09:14, 22 April 2022
- * 7 24VDC motors, 20w (3A) for Z axis and 3w (750mA) for the rest |Tried to get the z-axis moving, from the output end of the gearbox! Donated Arduino Mega for t11 KB (1,858 words) - 22:23, 7 March 2016
- | J7 || 9 || power ?? || RED Dout 15 Brake enable low to free Z axis | J10 || 1 || controller J8 || WHITE input ?? disable Z axis brake when low6 KB (837 words) - 23:19, 14 March 2022
- Processors Freescale MPC8241 @ 200Mhz *Dual 32-bit 33MHz Mini-PCI Slots7 KB (1,054 words) - 15:17, 3 June 2013
- == '''Larz''' ''<small>(aka Lawrence)</small>'' == ...ivered a few weeks ago. I've got it running with the standard Debian squeeze distribution.5 KB (810 words) - 09:09, 30 June 2012
- ===Adding a Cantilever Z Axis=== [[File:cupcake_cantilever_z_axis.jpg|thumb|350px|A cantilever Z-axis in laser cut acrylic.]]14 KB (2,609 words) - 02:17, 8 November 2012
- ...a repeating half-second beep on harmonics of 16.072MHz, including 144.648MHz. This starts about 10 seconds after boot, and is probably due to a TCO-745 1F01 60Hz5 KB (660 words) - 14:14, 29 May 2013
- ===Knowing the correct Z-Axis position=== ...worth noting that this is at the same height as the bottom edge of the horizontal ruler that runs along the length of the bed so may be easier to judge9 KB (1,566 words) - 07:06, 12 March 2022
- |location=Gone <!-- Floor, room/zone and location within that area --> ...a drill, they get clamped onto the spindle with a nut, there's different sizes depending on the shaft of the bit that you're using, and because bits are9 KB (1,564 words) - 08:34, 27 March 2019
- * Limit to a-z A-Z and 0-94 KB (584 words) - 00:55, 15 January 2019
