Difference between revisions of "Equipment/HPC LS3060 Laser Cutter"
Jump to navigation
Jump to search
Line 49: | Line 49: | ||
====Powering on==== | ====Powering on==== | ||
====Uploading your data file==== | ====Uploading your data file==== | ||
+ | '''TODO''' | ||
+ | * Different file types pros/cons | ||
+ | * Setting the scale | ||
+ | * Setting the origin - what to watch out for | ||
+ | * Who do you know when the file is sent successfully | ||
+ | |||
====Positioning your material==== | ====Positioning your material==== | ||
====Cutting==== | ====Cutting==== |
Revision as of 09:03, 15 September 2010
Logbook
15/09/2010 Operator Russ
- Cut some 1.5mm neoprene fairly successfully - needs high power and it's a bit smelly. (Settings in the book.)
- Circle issue is fixed. It was a problem with the tension on the frontmost X drive belt.
- Did some awesome etching onto black anodised aluminium - 450mm/sec, 90% power.
13/09/2010 Operator: samthetechie
Todo: Test CorelDraw X3 with 20mm circles on paper and compare to test using LaserCutter Software
12/09/2010 Operator: samthetechie
- Setup CorelDraw X3 with LaserCutter Add-on Toolbar.
- Cut Mic On Sign 3mm Perspex.
- Cut MusicMetric Sign 6mm MDF.
Model
- HPC LS3060 "plus" laser engraver and cutter.
Specification
Laser: | 40W - water cooled CO2 laser. |
Working area: | 320 x 600mm honeycomb bed (cutting area possibly about 300 x 550mm) |
Features: | Air-assist (removes debris from cutting region),
red-dot pointer (to show beam location) |
Water cooling: | Simple tube cooling circuit connected with (9mm OD, 6mm ID) latex tube.
Uses supplied submersible pond pump (2.8m head, 2800L/H flow). |
Safety information
*** Please don't touch or fiddle with the laser cutter unless you've had permission from either Russ or Jonty. ***
- Please don't affect the cooling system without consultation - overheating or rapid cooling can damage the laser.
- Never leave the laser cutter unattended - Your material may ignite, and an unchecked fire in the laser cutter could be both dangerous and costly.
- In case of fire - Use only the CO2 extinguisher positioned by the cutter.
- Never cut PVC or chlorinated plastic - You should always know what material you are cutting, and chlorinated plastics should be avoided because they release chlorine gas when cut.
- Do not try to cut metal in the laser cutter - If you wish to mark the metal, please use "Thermark Laser Engraving Spray / Paste", or use anodised aluminium.
Instructions
Powering on
Uploading your data file
TODO
- Different file types pros/cons
- Setting the scale
- Setting the origin - what to watch out for
- Who do you know when the file is sent successfully
Positioning your material
Cutting
Parameters for different materials
Cutting
Material | Thickness | Speed | Power | Corner power | Examples |
---|---|---|---|---|---|
Ply wood | 3mm | ? | ? | ? | some images |
Engraving
Material | Thickness | Speed | Power | Corner power | Examples |
---|---|---|---|---|---|
Ply wood | 3mm | ? | ? | ? | some images |
Tips
- Some useful laser info from Adafruit - the settings section in particular gave a good idea of what we can expect.
- More information about the controller card used by the cutter
Consumables
- HPC sheet products - Laser ply, perspex, engraving laminate - where we purchased the cutter.
- The Plastics Shop - mattp purchased the plastic for the first batch of Hackspace key rings from here.