Pledge: Collet Chuck: Difference between revisions
From London Hackspace Wiki
Deanforbes (talk | contribs) |
|||
| (26 intermediate revisions by 2 users not shown) | |||
| Line 6: | Line 6: | ||
The lathe is great but it is really not possible to work on smaller bits safely or accurately the new collet chuck will enable us to work on material between 1 and 20 mm safely or accurately | The lathe is great but it is really not possible to work on smaller bits safely or accurately the new collet chuck will enable us to work on material between 1 and 20 mm safely or accurately | ||
There has been good support for this and it has kind of would up being a successful shopping list - thanks for all the support :-) | |||
* lathe chuck and backplate | * lathe chuck and backplate | ||
===Budget estimation=== | ===Budget estimation=== | ||
* Backplate £41.22 Inc.VAT | * Backplate £41.22 Inc.VAT | ||
* Chuck £59.90 Inc.VAT | * Chuck £59.90 Inc.VAT | ||
Part Two | |||
* Mag Magnetic Base £21.76 | |||
* Dial Indicator Pin Type £8.96 | |||
* Dial Indicator Finger £16.99 | |||
Part Three | |||
* 1/2 Inch Torque wrench £21.95 | |||
==Pledges== | ==Pledges== | ||
* £10 -- ____ -- Des Quilty | |||
* £20 -- CASH -- Dean Forbes | |||
* £20 -- ____ -- Mike Karliner | |||
* £20 -- CASH -- Liam Lynch | |||
* £10 -- CASH-- Andrew Ruegg | |||
* £20 -- PAID -- Jonathan Hodgson | |||
* £20 -- PAID -- AJP2 | |||
* £20 -- CASH -- Richard Wood | |||
* £20 -- CASH -- Tim Jacobs | |||
==Payment== | |||
Please pay in your pledges into the hackspace account directly (same as membership) account and make sure to use the reference Collet_Chuck, once paid please mark them as PAID on this page . | |||
Running total: '''£160''' | |||
Approximate target: '''£162''' | |||
Paid UP: '''£130''' | |||
Cash Received '''£90.00''' | |||
[[Category:Pledges]] | [[Category:Pledges]] | ||
Latest revision as of 20:40, 9 June 2019
We are looking at purchasing a collet chuck and backing plate for the space. Pledge opened: 01.06.2019
Pledge leader: deanforbes
The item
The lathe is great but it is really not possible to work on smaller bits safely or accurately the new collet chuck will enable us to work on material between 1 and 20 mm safely or accurately
There has been good support for this and it has kind of would up being a successful shopping list - thanks for all the support :-)
- lathe chuck and backplate
Budget estimation
- Backplate £41.22 Inc.VAT
- Chuck £59.90 Inc.VAT
Part Two
- Mag Magnetic Base £21.76
- Dial Indicator Pin Type £8.96
- Dial Indicator Finger £16.99
Part Three
- 1/2 Inch Torque wrench £21.95
Pledges
- £10 -- ____ -- Des Quilty
- £20 -- CASH -- Dean Forbes
- £20 -- ____ -- Mike Karliner
- £20 -- CASH -- Liam Lynch
- £10 -- CASH-- Andrew Ruegg
- £20 -- PAID -- Jonathan Hodgson
- £20 -- PAID -- AJP2
- £20 -- CASH -- Richard Wood
- £20 -- CASH -- Tim Jacobs
Payment
Please pay in your pledges into the hackspace account directly (same as membership) account and make sure to use the reference Collet_Chuck, once paid please mark them as PAID on this page .
Running total: £160
Approximate target: £162
Paid UP: £130
Cash Received £90.00
