Equipment/HPC LS3060 Laser Cutter: Difference between revisions

From London Hackspace Wiki
Line 47: Line 47:


==Instructions==
==Instructions==
These instructions are intended as a companion to laser cutter safety training - not a replacement.
These instructions are intended as a companion to [[Workshops#Regular_Hackspace_workshops|laser cutter safety training]] - not a replacement.
====Powering on====
====Powering on====
# Insert key and turn
# Insert key and turn

Revision as of 13:14, 15 September 2010

Laser-cutter-installed.jpg
Laser-cut-key-rings.jpg

Logbook

15/09/2010 Operator Russ

  • Cut some 1.5mm neoprene fairly successfully - needs high power and it's a bit smelly. (Settings in the book.)
  • Circle issue is fixed. It was a problem with the tension on the frontmost X drive belt.
  • Did some awesome etching onto black anodised aluminium - 450mm/sec, 90% power.

13/09/2010 Operator: samthetechie

Todo: Test CorelDraw X3 with 20mm circles on paper and compare to test using LaserCutter Software

12/09/2010 Operator: samthetechie

Model

  • HPC LS3060 "plus" laser engraver and cutter.

Specification

Laser: 40W - water cooled CO2 laser.
Working area: 320 x 600mm honeycomb bed (cutting area possibly about 300 x 550mm)
Features: Air-assist (removes debris from cutting region),

red-dot pointer (to show beam location)

Water cooling: Simple tube cooling circuit connected with (9mm OD, 6mm ID) latex tube.

Uses supplied submersible pond pump (2.8m head, 2800L/H flow).

Safety information

Please don't touch or fiddle with the laser cutter unless you've had permission from either Russ or Jonty.
  • Please don't affect the cooling system without consultation - overheating or rapid cooling can damage the laser.
  • Never leave the laser cutter unattended - Your material may ignite, and an unchecked fire in the laser cutter could be both dangerous and costly.
  • In case of fire - Use only the CO2 extinguisher positioned by the cutter.
  • Never cut PVC or chlorinated plastic - You should always know what material you are cutting, and chlorinated plastics should be avoided because they release chlorine gas when cut.
  • Do not try to cut metal in the laser cutter - If you wish to mark the metal, please use "Thermark Laser Engraving Spray / Paste", or use anodised aluminium.

Instructions

These instructions are intended as a companion to laser cutter safety training - not a replacement.

Powering on

  1. Insert key and turn
  2. Always perform the following pre-checks:
    1. Check that there is a CO2 fire extinguisher to hand.
    2. Check that the water pump is running
    3. Check that the extractor fan is on
  3. Caution: Be certain that the water coolant is at a suitable temperature.
    • If you are unsure if the cutter has been used recently, or you have been using the cutter for an extended period of time (an hour or so) check the temperature of the water using the infra-red thermometer.
    • If the water temperature is outside the acceptable operating range (22 ± 5 °C) then wait for the water to cool before using the cutter.

Uploading your data file

TODO

  • Different file types pros/cons
  • Setting the scale
  • Setting the origin - what to watch out for
  • Layers - how are they used
  • How do you know when the file is sent successfully

Positioning your material

TODO

  • Caution: Know your material - be absolutely certain that your material is safe to use in the laser cutter. If in doubt - ask.
  • Caution: There are a number of electrically live areas inside the cabinet towards the back. Be very careful when reaching around there as you may get a shock.
  • Setting the bed Z-axis
  • Viewing the bounding box with red-dot pointer

Cutting

TODO

  • Caution - never leave the machine unattended
  • Initiating the cut
  • Monitoring progress
    • What to watch out for
    • What to do in case of problems
  • What to try if the result is not what you expect

Parameters for different materials

If you found some sweet settings please share them here.

Cutting

Material Thickness (mm) Speed (mm/sec) Power (%) Corner power (%) Examples
Ply wood 3 ? ? ? some images

Engraving

Material Speed (mm/sec) Power (%) Corner power (%) Examples
Anodized aluminium 450 90 ? LHS logo on black phone

Tips

Consumables