OccupyWireless/Bdi-flash-program-M3-readme.txt

From London Hackspace Wiki
< OccupyWireless
Revision as of 17:02, 3 February 2012 by Samthetechie (talk | contribs) (Created page with "[???@??? ~]$ cd [???@??? ~]$ telnet 192.168.0.210 Trying 192.168.0.210... Connected to 192.168.0.210. Escape character is '^]'. BDI Debugger for Embedded PowerPC ================...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

[???@??? ~]$ cd [???@??? ~]$ telnet 192.168.0.210 Trying 192.168.0.210... Connected to 192.168.0.210. Escape character is '^]'. BDI Debugger for Embedded PowerPC

=====================

PHYS <address> converts an effective to a physical address MD [<address>] [<count>] display target memory as word (32bit) MDD [<address>] [<count>] display target memory as double word (64bit) MDH [<address>] [<count>] display target memory as half word (16bit) MDB [<address>] [<count>] display target memory as byte (8bit) DUMP <addr> <size> [<file>] dump target memory to a file MM <addr> <value> [<cnt>] modify word(s) (32bit) in target memory MMD <addr> <value> [<cnt>] modify double word(s) (64bit) in target memory MMH <addr> <value> [<cnt>] modify half word(s) (16bit) in target memory MMB <addr> <value> [<cnt>] modify byte(s) (8bit) in target memory MC [<address>] [<count>] calculates a checksum over a memory range MV verifies the last calculated checksum RD [<name>] display general purpose or user defined register RDUMP [<file>] dump all user defined register to a file RDSPR <number> display special purpose register RDSR <number> display segment register RDVR [<number>] display vector register RM {<nbr>|<name>} <value> modify general purpose or user defined register RMSPR <number> <value> modify special purpose register RMSR <number> <value> modify segment register RMVR <nbr><val val val val> modify vector register (four 32bit values) ICACHE <addr | set> display L1 inst cache content (only MPC83xx/755) DCACHE <addr | set> display L1 data cache content DTLB <from> [<to>] display data TLB entry (only MPC83xx) ITLB <from> [<to>] display inst TLB entry (only MPC83xx) L2CACHE <addr | set> display L2 cache content (only 750FX/GX) UPMR <MxMR> <MDR> <addr> read selected UPM array RESET [HALT | RUN [time]] reset the target system, change startup mode BREAK [SOFT | HARD] display or set current breakpoint mode GO [<pc>] set PC and start target system TI [<pc>] trace on instuction (single step) TC [<pc>] trace on change of flow HALT force target to enter debug mode BI <addr> set instruction hardware breakpoint CI [<id>] clear instruction hardware breakpoint(s) BD [R|W] <addr> set data watchpoint via DABR (DABR[BT]=0) BDT [R|W] <addr> set data watchpoint via DABR (DABR[BT]=1) CD [<id>] clear data watchpoint(s) INFO display information about the current state LOAD [<offset>] [<file> [<format>]] load program file to target memory VERIFY [<offset>] [<file> [<format>]] verify a program file to target memory PROG [<offset>] [<file> [<format>]] program flash memory 

                                     <format> : SREC, BIN, AOUT or ELF

ERASE [<address> [<mode>]] erase a flash memory sector, chip or block 

                  <mode>  : CHIP, BLOCK or SECTOR (default is sector)

ERASE <addr> <step> <count> erase multiple flash sectors UNLOCK [<addr> [<delay>]] unlock a flash sector UNLOCK <addr> <step> <count> unlock multiple flash sectors FLASH <type> <size> <bus> change flash configuration DELAY <ms> delay for a number of milliseconds HOST <ip> change IP address of the host PROMPT <string> defines a new prompt string CONFIG display or update BDI configuration CONFIG <file> [<hostIP> [<bdiIP> [<gateway> [<mask>]]]] HELP display command list BOOT [loader] reboot the BDI and reload the configuration QUIT terminate the Telnet session

BDI> BDI>re - TARGET: processing user reset request - BDI asserts HRESET - Reset JTAG controller passed - Bypass check: 0x00000001 => 0x00000001 - JTAG exists check passed - COP status is 0x01 - Check running state passed - BDI scans COP freeze command - BDI removes HRESET - Target PVR is 0x80811014 - COP status is 0x05 - Check stopped state passed - Check LSRL length passed - BDI sets breakpoint at 0xFFF00100 - BDI resumes program execution - Waiting for target stop passed - TARGET: Target PVR is 0x80811014 - TARGET: resetting target passed - TARGET: processing target startup .... - TARGET: processing target startup passed BDI> BDI> BDI>erase 0xff800000 chip Erasing flash at 0xff800000 Erasing flash passed BDI> BDI> BDI>prog 0xfff00000 u932/ppcboot Programming u932/ppcboot , please wait .... Programming flash passed BDI> BDI> BDI>prog 0xff810000 u932/zImage Programming u932/zImage , please wait .... Programming flash passed BDI> BDI> BDI> BDI>prog 0xff940000 u932/r1.1/ramdisk Programming u932/r1.1/ramdisk , please wait .... Programming flash passed BDI> BDI> BDI> BDI>

Retrieved from ‘https://wiki.london.hackspace.org.uk/w/index.php?title=OccupyWireless/Bdi-flash-program-M3-readme.txt&oldid=20789’