Search results
Jump to navigation
Jump to search
- ...t in amplifier. The loudspeaker terminals on the back can produce up to 40 volts peak to peak and a lot more current than a typical 600ohm signal generator The two fuses on the right hand of the rear panel supply +45volts and -45volts to the amplifier module. The +ve fuse was ok and is a 2amp T fuse. A 250mA5 KB (806 words) - 18:22, 8 December 2019
- * Volts 230778 bytes (119 words) - 12:16, 19 January 2022
- ...use the vernier/range buttons to set the upper voltage you want (e.g. 1.2 volt) * Press the 'LOL' button and set the lower voltage (e.g. 0volt)4 KB (650 words) - 16:56, 29 May 2013
- * A 230 volt 110mm angle grinder and a selection of cutting wheels, and suitable gloves1 KB (180 words) - 11:27, 11 August 2015
- ...debug port at 2.5 volts, so you need to construct a circuit to convert the voltages from whatever your using. ''make this circuit (for a bus pirate (bit ba2 KB (203 words) - 00:15, 29 May 2013
- * MEASURE:VOLT:DC ...B address 10 - ask it to identify itself - and then proceed to measure the voltage (this will by default assume autoranging and adjust the settings as need3 KB (391 words) - 18:29, 29 May 2013
- ADC Voltage measurement probe (max 6volts) Vpu Voltage input for on-board pull-up resistors (0-5volts).6 KB (952 words) - 00:14, 29 May 2013
- ...d dimmed operations are stepped. There isn't a linear relationship between voltage and brightness. ! Volts1 KB (215 words) - 02:11, 2 March 2019
- ...00-fog-machine-224416|Prosound 400 N88GB] , Power: 400w , Fuse: T3A/250V , Volts: 230V/50HZ3 KB (491 words) - 23:23, 26 September 2013
- ..., we can deploy these fairly effectively as long as we have an adequate 12 volt power supply to drive them. ...tep Down DC Power Supply Converter] would be useful with all of the 16-19 volt laptop power supplies in bins at the hackspace that have been orphaned due8 KB (1,317 words) - 23:45, 16 May 2015
- ...the other; and then some RS-232 tranceiver (SP213EH) to lift TTL to RS232 voltages. ...similar variant which brings the 5v of the USB logic to the required RS232 voltages. We're now after the 5 FTDI wires:3 KB (565 words) - 17:45, 2 October 2011
- Below are a few examples of topics about power control and design in low voltage circuits, I'm sure some of them overlap. Feel free to add more talks and |The mathematics of electronics, Watts, Ohms, Farads, Coulombs, Amperes, Volts || || |Paul Maidment, [[User:bradwood| Bradley Wood]], [[User:funkyhat| Ma3 KB (470 words) - 21:28, 15 January 2014
- ''2 x Arduino's going pop due to high voltage on PSU's. I have already stopped using these in the kits and requested a ...few random ones from their own stock and confirmed they are all giving 15 volts. I have been promised a refund and I shall use it to purchase regulated 9v5 KB (855 words) - 18:08, 8 May 2013
- * 12 volts, 1 amp output, 1.5 amp maximum (including battery charging)4 KB (577 words) - 17:47, 21 July 2012
- ...wer supply was current limited to 0.8 amps, so voltage dropped to about 80 volts as the electrophoresis progressed)22 KB (3,613 words) - 00:17, 25 April 2014
- ...G rail which can be fed from USB or PWR in, solder bridge selection (diode volts drop too much for wired OR). Solder bridge for VUNREG to VCC or regulator6 KB (967 words) - 10:26, 30 November 2011
- AC Volts in an RC Circuit {{#ev:youtube|boAJIrGaEbU}}8 KB (1,199 words) - 16:33, 20 August 2016
- ...wear) tungsten tip where a plasma 'flame' is created (started with a high-voltage / high frequency starter) and used to heat the filler wire and joint. Th ...socket connection is used, with a pushbutton on/off control station and no-volt release.<br/>8 KB (1,203 words) - 08:23, 2 September 2024
- ...a bolt designed to induce neuromuscular incapacitation; and therefore 1200 volts instead of a creep. ...Cambridge and none at all in the hackspace. It is very sensitive to supply voltage smoothness.11 KB (1,923 words) - 17:33, 28 May 2013