Difference between revisions of "Equipment/Prologix GPIB-USB controller"
Jump to navigation
Jump to search
m |
|||
(3 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
+ | {{EquipmentInfobox | ||
+ | | name = Prologix GPIB-USB controller <!-- Name of the item. --> | ||
+ | | image = Hackspace_Unknown.png <!-- Image of the item. Leave with placeholder image if none exists. --> | ||
+ | | model = Unknown <!-- Model --> | ||
+ | | category = Equipment <!-- Main category. Please leave alone to keep item in this category --> | ||
+ | | subcat = Test equipment<!-- Sub-category if one exists. Please check main listing to see other categories contained within the main one --> | ||
+ | | status = <!-- Set to one of; Good working order, Faulty, Out of order, Under construction, Out of consumables, Scrapped, or Unknown --> | ||
+ | | consumables = Unknown <!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. --> | ||
+ | | accessories = Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> | ||
+ | | reqtraining = <!-- Is training required to use this equipment? Yes or no. --> | ||
+ | | trainlink = Unknown <!-- If training is required, provide a link to training signup or contact page. Otherwise leave blank. --> | ||
+ | | acnode = <!-- Is the equipment ACnode locked? --> | ||
+ | | owner = Unknown <!-- Provide a link to owners members page if other than LHS --> | ||
+ | | origin = Unknown <!-- If via pledge, please link to the completed pledge page on the wiki --> | ||
+ | | location = <!-- Floor, room/zone and location within that area --> | ||
+ | | maintainers = <!-- NO LINKS PLEASE; it currently breaks the template. If someone is nominated as managing the upkeep of this item, please list them here. --> | ||
+ | | template_ver = 1.1 <!-- Please do not change. Used for tracking out-of-date templates --> | ||
+ | }} | ||
+ | |||
There is a Prologic GPIB to Ethernet adaptor available in the electronics area. It connects a couple of meters to ethernet - and lets one do some automation on capture. | There is a Prologic GPIB to Ethernet adaptor available in the electronics area. It connects a couple of meters to ethernet - and lets one do some automation on capture. | ||
Line 19: | Line 38: | ||
This device is *not* to hack - just to aid your hacking :) | This device is *not* to hack - just to aid your hacking :) | ||
− | == current devices | + | == current devices == |
− | * ADDR 6 -- Programmable Power supply/cycler | + | * ADDR 6 -- Programmable Power supply/cycler |
+ | * ADDR 7 -- HP8112 Signal generator | ||
* ADDR 9 -- HP3488A Electronic Switch Unit | * ADDR 9 -- HP3488A Electronic Switch Unit | ||
− | * ADDR 10 -- SOLARTRON SCHLUMBERGER 7150N Multimeter | + | * ADDR 10 -- SOLARTRON SCHLUMBERGER 7150N Multimeter |
Latest revision as of 18:29, 29 May 2013
Prologix GPIB-USB controller | |
---|---|
Model | Unknown |
Sub-category | Test equipment |
Consumables | Unknown |
Accessories | Unknown |
Training link | Unknown |
Owner | Unknown |
Origin | Unknown |
There is a Prologic GPIB to Ethernet adaptor available in the electronics area. It connects a couple of meters to ethernet - and lets one do some automation on capture.
- MAC Address: 00:21:69:01:05:57 a
- Usually on IP Address 172.31.24.126
- [Documentation]
- Responds to 3040 discovery and telnet to port 1234
Typical use session:
- telnet 172.31.24.126 1234
- ++addr 10
- *IDN?
- HP127812
- MEASURE:VOLT:DC
- 12.3912
I.e. telnet to the box, talk to GPIB address 10 - ask it to identify itself - and then proceed to measure the voltage (this will by default assume autoranging and adjust the settings as needed).
This device is *not* to hack - just to aid your hacking :)
current devices
* ADDR 6 -- Programmable Power supply/cycler * ADDR 7 -- HP8112 Signal generator * ADDR 9 -- HP3488A Electronic Switch Unit * ADDR 10 -- SOLARTRON SCHLUMBERGER 7150N Multimeter