Project:Tool Access Control/Deployment

This page is for keeping track of what we need to achieve, and how far along we are to achieving it.

Tools

node id	name	battery backup	lock type	RFID module	PCB	PSU	MAC Address	IPv4 Addr	Status	Notes	Card cache	MQTT Topic Base	Software Door release
1	back doorbot	7Ah SLA	Gianni EB300 solenoid bolt	Elechouse NFC module v3	acnode/doorbot board	in enclosure, mains fed	00:1a:b6:03:03:47		In Service		RAM	/door/gf-back	Installed and active
3	LulzBot_Hull	nil	n/a	Elechouse NFC module v4	wire wrap	in enclosure, wall wart	00:1A:B6:02:B2:18	10.0.40.3	In Service	SSR	eeprom	/tool/hull
4	LulzBot_Crump	nil	n/a	Elechouse NFC module v3	acnode board rev 2	in enclosure, wall wart	00:1A:B6:02:BF:6F	10.0.40.4	In Service	SSR in tool itself	eeprom	/tool/crump
5	Ground floor doorbot	7Ah SLA	Gianni EB300 solenoid bolt	Elechouse NFC module v4	acnode shield rev 4, also acnode board rev 2 for pinouts		00:1A:B6:02:F3:F5	10.0.40.5	In Service	built into same enclosure as Front Doorbot. RFID reader to be placed on glass door	RAM	/door/gf-front-inner	Installed and active
6	Front doorbot	7Ah SLA	landlord's maglock, remote relay release	Deek-Robot	acnode shield rev 4, also acnode board rev 2 for pinouts		00:1A:B6:03:12:F4	10.0.40.6	In Service	Landlord's maglock, powered by landlord's PSU, installed relay to interrupt. Door release is Landlord's, with timed release via their door entry system	RAM	/door/gf-front-external	N/A - landlord's door release
8	Biolab restricted doorbot	7Ah SLA		Elechouse NFC module v4	acnode shield rev 4, also acnode board rev 2 for pinouts		90:A2:DA:00:F3:C3	10.0.40.8	In Service	Shared enclosure and PSU with back gate cage doorbot	RAM	/door/gf-biolab	Installed and active
10	Radio room restricted doorbot	7AH SLA	maglock	Deek-Robot	acnode shield rev 4, also acnode board rev 2 for pinouts	in enclosure	00:1A:B6:03:44:BF		In Service	in same enclosure as Electronics Room doorbot	RAM	/door/1f-funk (because "radio" is cooler in german)	Installed and active
11	lasercutter	nil	n/a	Elechouse NFC module v4	acnode board rev 2	POE splitter	00:1A:B6:02:CB:75	10.0.40.11	In Service	SSR in acnode enclosure	eeprom	/tool/laz0rz
12	Back gate cage doorbot		maglock	Elechouse NFC module v4	acnode/doorbot board		00:1a:b6:02:d9:4b	10.0.40.12	In Service	Shared enclosure and PSU with biolab doorbot	sdcard	/door/gf-backgate	Installed and active
13	Hopper	nil	n/a		LHS vending machine board				Vending Machine. Under construction	Neither door, nor tool, registered in acserver as a door	n/a
14	SSR only ready for deployment	nil			acnode board rev 2					single phase AC
15	Colchester Master Lathe	nil	n/a	Deek-Robot	acnode/doorbot board	POE splitter	00:1a:b6:03:41:51	10.0.40.15	In Service	3-phase but possible single phase low-current control cable numbers 22/23	eeprom	/tool/colchester
16	Bridgeport Mill	nil	n/a	Deek-Robot	acnode/doorbot board	POE splitter	00:1A:B6:03:41:4A	10.0.40.16	In Service	Interrupts 110V power to e-stop circuit. acnode powered via PoE	eeprom	/tool/bridgeport
17	Tool Store	7Ah SLA	maglock	Elechouse NFC module v4	acnode/doorbot board	in enclosure	00:1A:B6:03:52:70	10.0.40.17	In Service	built into same enclosure as back doorbot		/door/gf-toolstore
18	Sedgwick TA315 Table Saw	nil	n/a	Elechouse NFC module v4	acnode board rev 2		00:1A:B6:02:CD:98	10.0.40.18	In Service	single phase AC. 16A commando		/tool/sedgwick
	Wishlist for acnode/doorbot controlled equipment below here
	De Walt Table Saw									single phase AC. SSR
	Woodworking lathe									single phase AC, 13A
19	Planer	nil	n/a	Deek-Robot	acnode board rev 2		00:1a:b6:02:cc:d9	10.0.40.19	In Service	single phase 16A. SSR
20	Radial Arm Saw	nil	n/a		acnode shield rev 4		00:1A:B6:03:08:0A					/tool/ras

If an acnode crashes and is fed by PoE, then try unplugging the network cable and re-plugging it. The indicator LED on the button should rainbow cycle while rebooting.

Items in stock

• 1x Connected Launchpads
• 3x 40A SSRs - please don't use
• 3x RFID Readers
• 0x RGB LED arcade buttons