Difference between revisions of "Equipment/DrillPress"
Jump to navigation
Jump to search
m |
|||
| (18 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
{{EquipmentInfobox | {{EquipmentInfobox | ||
| − | | name = Drill press <!-- Name of the item. --> | + | |name=Drill press <!-- Name of the item. --> |
| − | | image = | + | |image=Axminster ED16SB.jpg |
| − | | model = | + | |model=Axminster ED16SB<!-- Model --> |
| − | | category = Equipment <!-- Main category. Please leave alone to keep item in this category --> | + | |category=Equipment <!-- Main category. Please leave alone to keep item in this category --> |
| − | | subcat = | + | |subcat=defunt |
| − | | status = | + | |status=Disposed of |
| − | | consumables = | + | |consumables=oil, cutting fluid,drive belt<!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. --> |
| − | | accessories = Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> | + | |accessories=Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> |
| − | | reqtraining = <!-- Is training required to use this equipment? Yes or no. --> | + | |reqtraining=No<!-- Is training required to use this equipment? Yes or no. --> |
| − | | trainlink = Unknown <!-- If training is required, provide a link to training signup or contact page. Otherwise leave blank. --> | + | |trainlink=Unknown <!-- If training is required, provide a link to training signup or contact page. Otherwise leave blank. --> |
| − | | acnode = No<!-- Is the equipment ACnode locked? --> | + | |acnode=No<!-- Is the equipment ACnode locked? --> |
| − | | owner = LHS<!-- Provide a link to owners members page if other than LHS --> | + | |owner=LHS<!-- Provide a link to owners members page if other than LHS --> |
| − | | origin = Unknown <!-- If via pledge, please link to the completed pledge page on the wiki --> | + | |origin=Unknown <!-- If via pledge, please link to the completed pledge page on the wiki --> |
| − | | location = | + | |location=Woodshop |
| − | | maintainers = <!-- NO LINKS PLEASE; it currently breaks the template. If someone is nominated as managing the upkeep of this item, please list them here. --> | + | |maintainers=sjrapid<!-- NO LINKS PLEASE; it currently breaks the template. If someone is nominated as managing the upkeep of this item, please list them here. --> |
| − | | template_ver = 1.1 <!-- Please do not change. Used for tracking out-of-date templates --> | + | |template_ver=1.1 <!-- Please do not change. Used for tracking out-of-date templates --> |
}} | }} | ||
| + | ==Status== | ||
| + | '''Works, but is not very precise!''' | ||
| + | |||
| + | 9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out with a dial indicator. | ||
| + | |||
| + | Quill runout is approximately 0.2mm (should be <=0.02mm, 1thou) ). Runout at the chuck can be anything up to 10x this depending on selected speed and cutting bit. Your holes may be oval! | ||
| + | |||
| + | Here's the dial-indicator test video: | ||
| − | + | [http://www.flickr.com/photos/flux-org-uk/9469751707/ Drill press precision] | |
| − | + | ||
| + | There is a [[Pledge:_Drill_Press|pledge]] running to get a new Drill Press for the space. | ||
| − | + | The space has an Axminster drill press. The keyless chuck only goes down to 2.7 mm, so for anything smaller you need a "[http://uk.farnell.com/multicomp/143-0127/pin-chuck-auto-3-jaw/dp/1518437 pin chuck]". | |
| + | Or you can use the Dremel and mini-mill for high speed / light duty / precision stuff. | ||
Ideal jobs : | Ideal jobs : | ||
| Line 40: | Line 50: | ||
* Manual: [http://www.axminster.co.uk/downloads/700101_manual.pdf on the Axminster website] | * Manual: [http://www.axminster.co.uk/downloads/700101_manual.pdf on the Axminster website] | ||
| + | == Pictures == | ||
| + | {| | ||
| + | |[[File:Drill_press_non_stock.jpg|thumb|The Hackspace drill press, from the front]] | ||
| + | |[[File:Drill_press_side.jpg|thumb|The Hackspace drill press, from the side]] | ||
| + | |[[File:Drill_press_other_side.jpg|thumb|The Hackspace drill press, from the other side]] | ||
| + | |} | ||
==Log== | ==Log== | ||
| Line 46: | Line 62: | ||
#<artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard. | #<artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard. | ||
#<artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely | #<artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely | ||
| − | |||
#<lovelace_> K, seems firmly in now | #<lovelace_> K, seems firmly in now | ||
| − | # | + | #9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out under no load with a dial indicator. Also tested with a new certified chuck and arbour (0.0012 TIR). Measured run out of about 0.25mm on the new chuck. TIR not measured on the existing keyless chuck. |
Latest revision as of 20:17, 23 March 2019
| Drill press | |
|---|---|
 | |
| Model | Axminster ED16SB |
| Sub-category | defunt |
| Status | Disposed of |
| Consumables | oil, cutting fluid,drive belt |
| Accessories | Unknown |
| Training requirement | No |
| Training link | Unknown |
| ACnode | No |
| Owner | LHS |
| Origin | Unknown |
| Location | Woodshop |
| Maintainers | sjrapid |
Status
Works, but is not very precise!
9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out with a dial indicator.
Quill runout is approximately 0.2mm (should be <=0.02mm, 1thou) ). Runout at the chuck can be anything up to 10x this depending on selected speed and cutting bit. Your holes may be oval!
Here's the dial-indicator test video:
There is a pledge running to get a new Drill Press for the space.
The space has an Axminster drill press. The keyless chuck only goes down to 2.7 mm, so for anything smaller you need a "pin chuck".
Or you can use the Dremel and mini-mill for high speed / light duty / precision stuff. Ideal jobs :
Dremel
- High speed, tiny bits e.g. PCB drilling
Mini-Mill
- Milling plastic, small aluminium etc.
- Drilling jobs requiring accurate positioning - use the table positioning
Drill Press
- Most general purpose drilling jobs
Model
- Make: Axminster
- Model: ED16SB
- Manual: on the Axminster website
Pictures
Log
- <lovelace_> The chuck for the new stand drill falls out easily
- <lovelace_> I can't see how it tightens up
- <artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard.
- <artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely
- <lovelace_> K, seems firmly in now
- 9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out under no load with a dial indicator. Also tested with a new certified chuck and arbour (0.0012 TIR). Measured run out of about 0.25mm on the new chuck. TIR not measured on the existing keyless chuck.