Difference between revisions of "Laser Cutter/Instructions"

From London Hackspace Wiki
Jump to navigation Jump to search
(Restore "Checking cutting boundaries" section, which disappeared some reevisions ago)
 
(52 intermediate revisions by 10 users not shown)
Line 3: Line 3:
 
Refresher instructions found at [[Equipment/LaserCutter/Refresher]]
 
Refresher instructions found at [[Equipment/LaserCutter/Refresher]]
 
==Powering on==
 
==Powering on==
# Insert key and turn - the PC is turned on using the 'sleep' button on the keyboard.
+
# Place your card on the reader, insert key and turn.
 +
#* If you turn the key on and nothing happens, check that the Emergency Stop (the big red button) is not locked down. If it is, turn it until is springs up and the laser cutter machine should power up.
 +
# The PC is turned on using the 'e' button on the front of the PC (black PC with DNH "CCTV machine" label).
 +
#* The password for the PC (the Laser Cutter User) is: "hackspace"
 
# '''Always''' perform the following pre-checks:
 
# '''Always''' perform the following pre-checks:
 
## Check that there is a '''CO<sub>2</sub>''' fire extinguisher '''immediately to hand'''.
 
## Check that there is a '''CO<sub>2</sub>''' fire extinguisher '''immediately to hand'''.
Line 9: Line 12:
 
## Check that the extractor fan is on AND that air is flowing. You should be able to feel it at the mouth of the extraction tube.
 
## Check that the extractor fan is on AND that air is flowing. You should be able to feel it at the mouth of the extraction tube.
 
# '''Caution:''' Be certain that the water coolant is at a suitable temperature.
 
# '''Caution:''' Be certain that the water coolant is at a suitable temperature.
#* If you are unsure if the cutter has been '''used recently''', or you have been using the cutter for an '''extended period of time''' (an hour or so) check the temperature of the water using the infra-red thermometer.
+
#* If you are unsure if the cutter has been '''used recently''', or you have been using the cutter for an '''extended period of time''' (an hour or so) check the temperature of the water on the black box over the tank.
 
#* If the water temperature is outside the acceptable operating range (22 &plusmn; 3 &deg;C) then wait for the water to cool before using the cutter.
 
#* If the water temperature is outside the acceptable operating range (22 &plusmn; 3 &deg;C) then wait for the water to cool before using the cutter.
  
 
==Preparing your design==
 
==Preparing your design==
* Produce your design. There are various options for doing this
+
Produce your design. There are various options for doing this
** [[Equipment/LaserCutter/QCad|QCad]]  - a good low cost choice
 
** [[Guides/InkscapeForLaserCutting|Inkscape]] - Free
 
** [[Guides/SketchUp_for_Laser_Cutting|SketchUp]] - Note that you need a plugin to export DXF files
 
* Start the 'LaserCut' application and load/import your design.
 
* '''TODO''' Different file types pros/cons
 
** DXF is nice because it maintains absolute dimensions.
 
* Sometimes it's useful scale your design. The Laser cutter application allows for this but it's rather quirky:
 
** From the Laser software menu select 'Tools/Size'
 
** Calculate and enter your new widths/heights in Google/calc etc.
 
* Rotating
 
** Go to 'Draw/rotal'
 
** Enter the number of degrees to rotate
 
* Uniting lines (making the path finding suck a little less)use this if you've used lines rather than polylines is qcad etc.
 
** Go to 'Tools/Unite lines'
 
** Use the defaults
 
** You should see fewer direction lines, the laser cutter should use a less insane route now.
 
* The work-area in the LaserCut software is not an absolute representation of the laser cutter bed. The origin must be set relative to your design.
 
** From the LaserCut application menu select 'Laser/Set laser origin'
 
  
[[File:Laser-Cutter-Screen-Origin-1.png|center|'Laser/Set laser origin']]
+
==== Software packages ====
  
** Move the 'target' cursor and click on the location on your design where you wish to position the origin (this is usually at the top right of the design)
+
===== Qcad =====
** You may also manually enter the position - the top corner of bed is located at (299, 559)
+
[[Equipment/LaserCutter/QCad]]
  
[[File:Laser-Cutter-Screen-Origin-2.png|center|manually enter the position]]
+
A good low cost choice
  
* Layers can be used in your design to provide combinations of different cut types and engrave options on a single piece. For example you may wish to cut out a key-ring and then engrave a name on it.
+
===== Inkscape =====
** Each layer can be assigned different action, speed and power settings - consult the manual or the [[#Parameters_for_different_materials|wiki]] for appropriate settings.
+
[[Guides/Inkscape_for_Laser_Cutting]]
** Finer control of layer power and speed settings is available by clicking on the layer.
 
  
[[File:Laser-Cutter-Screen-Cut-options.png|center|clicking on the layer]]
+
Free and used by many other Hackspaces
  
==Engraving==
+
===== SketchUp =====
** Try to align the bulk of the engraving with the short axis (y), the laser cutter seems to do passes in this direction only so if you have it aligned to the long (x) axis it will do many short passes rather than fewer longer ones, this can '''massively''' increase engraving time (minutes -> hours)
+
[[Guides/SketchUp_for_Laser_Cutting]]
** Rather than slow down/increase power there is a setting to repeat a layer multiple times, this is very useful if using the engrave option to reach a certain depth.
+
 
** For fast prototypes the engraving step size can be changed (default is 0.1mm) a setting of 0.2 is good for depth engraving, again this can speed up the process a lot.
+
You will need a plugin to export DXF files
* '''Note''' if something hasn't cut/engraved to the complete depth (or you just want to run it again) it is possible to select which layers are 'output' by scrolling to the right in the layers box, this is very useful for an extra layer of engraving or to confirm a full cut. DON'T move the sheet before doing this.
+
 
 +
===== Illustrator =====
 +
[[Guides/Illustrator_for_Laser_Cutting]]
 +
 
 +
Export files as DXF or AI
 +
 
 +
===== FreeCAD =====
 +
Although strictly a 3d tool, it can do 2d sketch exports.
 +
It's nice since it is fairly parametric so you can specify dimensions properly.
 +
 
 +
It's a bit tricky to get the files into a format usable by Lasercut53 - here's what worked for me:
 +
# Export as DXF as per [https://www.freecadweb.org/wiki/FreeCAD_and_DXF_Import|the FreeCAD docs]
 +
# Open in Librecad
 +
# Explode the object
 +
# Resave as DXF R12
 +
 
 +
The explode seems to be surprisingly important otherwise it will either give an error, or silently import nothing!
 +
 
 +
==Using the laser cutter==
 +
 
 +
==== Use Lightburn software ====
 +
 
 +
Video Tutorials
 +
 
 +
https://www.youtube.com/watch?v=nybhYtjElQU
  
==Uploading your data file==
 
* Upload the file to the design and settings to the laser cutter hardware as follows:
 
** Select the 'Download' button
 
[[File:Laser-Cutter-Screen-Download.png|center|'Download' button]]
 
** Remove any existing files by selecting them and clicking 'Del all'
 
** Download (upload) your file by clicking 'Download current'
 
  
 
==Positioning your material==
 
==Positioning your material==
Line 70: Line 72:
  
 
===Setting the Z-Axis===
 
===Setting the Z-Axis===
There are two methods for setting the Z-Axis:
 
  
 
# '''Software Method (preferred)'''
 
# '''Software Method (preferred)'''
 
#* The +/-Z buttons in the laser cutting software are the preferred choice for setting the Z-Axis position.
 
#* The +/-Z buttons in the laser cutting software are the preferred choice for setting the Z-Axis position.
# '''Hardware Method'''
 
#* '''Note:''' This method is discouraged as the the panel is a bit shonky to use i.e. unregistered key presses and the cutter sometimes wont cut while in "Z axis mode".
 
#* Press the 'Z' button on the control panel.
 
#*: [[File:Laser-Cutter-Screen-Z-Axis.jpg|300px|center|control panel]]
 
#* The display will show 'Z-Axis operate'
 
#* Then press the 'Datum' button
 
#* The display should now show 'Z-Axis datum' and the bed will move to the 0 point. Now you use the up and down buttons to move the bed.
 
  
 
===Checking cutting boundaries===
 
===Checking cutting boundaries===
To make sure that your design will be cut within the boundary of your material you can have the
+
 
To make sure that your design will be cut within the boundary of your material you can have the cutter mark out the bounding box with the red-dot pointer. Note that you must upload your design to the cutter before doing this.
+
TODO
 
* Click the 'Run box' button in the laser cutter application
 
*: [[File:Laser-Cutter-Screen-Run-box.png|center|'Run box' button ]]
 
* Observe the path of the red-dot pointer
 
  
 
==Cutting==
 
==Cutting==
Line 95: Line 85:
 
* '''Caution:''' There are a number of electrically live areas inside the cabinet towards the back. Be very careful when reaching around at the back as you may get a shock.
 
* '''Caution:''' There are a number of electrically live areas inside the cabinet towards the back. Be very careful when reaching around at the back as you may get a shock.
 
* Know where the CO2 extinguisher is and that you can easily get to it without having to come nearer to the cutter.
 
* Know where the CO2 extinguisher is and that you can easily get to it without having to come nearer to the cutter.
[[File:Laser-Cutter-Screen-Control-panel.jpg|300px|center|main control panel]]
+
 
* To begin cutting press the 'Start' button in the laser cutter application.
 
[[File:Laser-Cutter-Screen-Start.png|center|'Start' button]]
 
 
* Monitoring progress
 
* Monitoring progress
** '''TODO''' What to watch out for
+
** What to watch out for
** '''TODO''' What to do in case of problems
+
** What to do in case of problems
**Note: There are at least 3 different ways of stopping the cutter mid-process. There is the emergency stop button on the cutter, there is the stop button in the software (not recommended), and there is a sensor that detects if the lid is opened. There is also a pause/resume button on the cutter.
+
*** Note: There are at least 3 different ways of stopping the cutter mid-process. There is the emergency stop button on the cutter, there is the stop button in the software (not recommended), and there is a sensor that detects if the lid is opened. There is also a pause/resume button on the cutter.
**Please be aware that the software stop button has on at least two occasions had the unfortunate effect of moving the laser back to the start position while it was still on, leaving unwanted lines cut into the material.
+
*** Please be aware that the software stop button has on at least two occasions had the unfortunate effect of moving the laser back to the start position while it was still on, leaving unwanted lines cut into the material.
* '''TODO''' What to try if the result is not what you expect
+
*** For any fires, or issues where the head has moved outside the cutting area, place an "Out of Order" sign on the machine and contact the [[Mailing List]].
* Log your Laser Cutter use in the [[Equipment/LaserCutter/LogBook|logbook]]
+
* '''.''' What to try if the result is not what you expect
  
When cutting flammable materials (or non-flammable materials which happen to emit gases which are flammable when cut) or materials with a thin oil/wax film - be prepared for fires or small flames. While not common - it does happen occasionally and should not be cause for panic. When it happens - press the stop button and use a small gentle blast of CO2 fire extinguisher to douse it. There is no need to get very close to the fire - generally the box 'fills' up with the CO2 gas which is heavier than air - esp. when things are not yet hot. Note this in the logbook (both so we can replace the CO2 and because of sooth on the lens).  Don't forget to report any fire in the logbook.
+
When cutting flammable materials (or non-flammable materials which happen to emit gases which are flammable when cut) or materials with a thin oil/wax film - be prepared for fires or small flames. While not common - it does happen occasionally and should not be cause for panic. When it happens - press the stop button and use a small gentle blast of CO2 fire extinguisher to douse it. There is no need to get very close to the fire - generally the box 'fills' up with the CO2 gas which is heavier than air - esp. when things are not yet hot. Note this in the logbook (both so we can replace the CO2 and because of soot on the lens).  Don't forget to report any fire to the [[Mailing List]].
  
 
In the unlikely event that you cannot contain the fire with CO2 - switch to the powder extinguisher. Do not use water (risk of electrical shock). If you use the real (sealed) extinguisher - post  an incident follow the accident/reporting protocol - to comply with fire, health and safety regulation.
 
In the unlikely event that you cannot contain the fire with CO2 - switch to the powder extinguisher. Do not use water (risk of electrical shock). If you use the real (sealed) extinguisher - post  an incident follow the accident/reporting protocol - to comply with fire, health and safety regulation.
  
 
If you are unfamiliar with fire extinguishers - and why there are many type - then read the instructions on both the CO2 and the ABC extinguisher (http://en.wikipedia.org/wiki/Fire_extinguisher) as to understand the difference.
 
If you are unfamiliar with fire extinguishers - and why there are many type - then read the instructions on both the CO2 and the ABC extinguisher (http://en.wikipedia.org/wiki/Fire_extinguisher) as to understand the difference.
 +
 +
==Logging use==
 +
 +
* Please log your Laser Cutter use in the [http://bit.ly/LaserLogbookForm Lasercutter logbook].
 +
** This is used to track how long the tube lasts, schedule maintenance, and keep an eye on any developing issues.
 +
** The time you have used the laser for is shown on the machine's display panel.
 +
 +
==Switching off & shutting down==
 +
 +
 +
* Put money in the box proportional to the amount of time you used (price displayed on sign next to machine).
 +
* Shutdown the computer from the start button on the desktop.
 +
* Clear any cutting debris from the laser cutter to help the next user and the maintainers.
 +
* Close the lid, turn off using the key, remove your card.
  
 
==What to do with Scraps==
 
==What to do with Scraps==
Line 127: Line 129:
 
#Heat copper wire until red hot again.
 
#Heat copper wire until red hot again.
 
#A green flame means that the plastic contains chlorine so do not use it.
 
#A green flame means that the plastic contains chlorine so do not use it.
 
==Changing machine options==
 
'''This is now passworded due to abuse, trustees and maintenance users know the code'''
 
 
advanced use only! Please make sure current settings are backed up first.
 
 
Click File->Machine Options. This will show you a dialog like this:
 
 
http://wiki.london.hackspace.org.uk/w/images/2/23/Machineoptions.PNG
 
 
Make your changes.
 
 
Useful that I've found is the Machine options -> worktable page. This allows adjustment of scaling for x and y axis. Decrease the numbers to increase the distance moved. I got good scaling with 0.00635 for both.
 
 
Then click 'save' and OK the password dialog. The settings won't become live until you download them to the cutter.
 
 
Click 'download' as if you were putting a new design on the cutter, but then click 'download cfg'. The machine should beep. I had problems with this and then cutting a pattern, the machine always told me 'soft stop'. I 'fixed' it by powering off the machine before downloading the new settings.
 
 
[[Category:Guides]]
 

Latest revision as of 07:06, 12 March 2022

These instructions are intended as a companion to laser cutter safety training - not a replacement.

Refresher instructions found at Equipment/LaserCutter/Refresher

Powering on

  1. Place your card on the reader, insert key and turn.
    • If you turn the key on and nothing happens, check that the Emergency Stop (the big red button) is not locked down. If it is, turn it until is springs up and the laser cutter machine should power up.
  2. The PC is turned on using the 'e' button on the front of the PC (black PC with DNH "CCTV machine" label).
    • The password for the PC (the Laser Cutter User) is: "hackspace"
  3. Always perform the following pre-checks:
    1. Check that there is a CO2 fire extinguisher immediately to hand.
    2. Check that the water pump is running
    3. Check that the extractor fan is on AND that air is flowing. You should be able to feel it at the mouth of the extraction tube.
  4. Caution: Be certain that the water coolant is at a suitable temperature.
    • If you are unsure if the cutter has been used recently, or you have been using the cutter for an extended period of time (an hour or so) check the temperature of the water on the black box over the tank.
    • If the water temperature is outside the acceptable operating range (22 ± 3 °C) then wait for the water to cool before using the cutter.

Preparing your design

Produce your design. There are various options for doing this

Software packages

Qcad

Equipment/LaserCutter/QCad

A good low cost choice

Inkscape

Guides/Inkscape_for_Laser_Cutting

Free and used by many other Hackspaces

SketchUp

Guides/SketchUp_for_Laser_Cutting

You will need a plugin to export DXF files

Illustrator

Guides/Illustrator_for_Laser_Cutting

Export files as DXF or AI

FreeCAD

Although strictly a 3d tool, it can do 2d sketch exports. It's nice since it is fairly parametric so you can specify dimensions properly.

It's a bit tricky to get the files into a format usable by Lasercut53 - here's what worked for me:

  1. Export as DXF as per FreeCAD docs
  2. Open in Librecad
  3.  Explode the object
  4. Resave as DXF R12

The explode seems to be surprisingly important otherwise it will either give an error, or silently import nothing!

Using the laser cutter

Use Lightburn software

Video Tutorials

https://www.youtube.com/watch?v=nybhYtjElQU


Positioning your material

The origin denoted in the cutter software corresponds to the top left corner of the cutting bed, so your material should be butted up against that corner. This means the X axis shown in the cutter is the axis parallel to the direction the user is facing, with left screen movement translating to movement towards the user. The on screen Y axis is the axis perpendicular to the user with on-screen down translating to movement to the right.

Knowing the correct Z-Axis position

The bed height must be adjusted to the thickness of your material so as to ensure the focus point of the beam is in the optimal position for your task. The focus point of the beam corresponds with the top edge of the vertical ruler that is attached to the back of the cutting area. It's worth noting that this is at the same height as the bottom edge of the horizontal ruler that runs along the length of the bed so may be easier to judge the correct height using that albeit a bit less intuitive to remember. So:

  • For cutting materials <=8mm, the bed height should be set to the focus point, making the bottom of your material the focus point of the laser (i.e. the top of the cutting bed should line up with the top of the vertical ruler).
  • For cutting materials >8mm, the bed height needs to be adjusted such that the focus point is in the mid point of the material.
  • For engraving, the focus point should be the top of your material.
  • There is no instance in which the bed height should ever be set to be higher than the bottom edge of the ruler / focus point.

Setting the Z-Axis

  1. Software Method (preferred)
    • The +/-Z buttons in the laser cutting software are the preferred choice for setting the Z-Axis position.

Checking cutting boundaries

TODO

Cutting

  • Caution: Never leave the machine unattended. The laser cuts and engraves by burning the material so you must be present to deal with any fires should this process undesirably escalate.
  • Caution: Know your material - be absolutely certain that your material is safe to use in the laser cutter. If in doubt - ask. For unidentified plastics try this test method.
  • Caution: There are a number of electrically live areas inside the cabinet towards the back. Be very careful when reaching around at the back as you may get a shock.
  • Know where the CO2 extinguisher is and that you can easily get to it without having to come nearer to the cutter.
  • Monitoring progress
    • What to watch out for
    • What to do in case of problems
      • Note: There are at least 3 different ways of stopping the cutter mid-process. There is the emergency stop button on the cutter, there is the stop button in the software (not recommended), and there is a sensor that detects if the lid is opened. There is also a pause/resume button on the cutter.
      • Please be aware that the software stop button has on at least two occasions had the unfortunate effect of moving the laser back to the start position while it was still on, leaving unwanted lines cut into the material.
      • For any fires, or issues where the head has moved outside the cutting area, place an "Out of Order" sign on the machine and contact the Mailing List.
  • . What to try if the result is not what you expect

When cutting flammable materials (or non-flammable materials which happen to emit gases which are flammable when cut) or materials with a thin oil/wax film - be prepared for fires or small flames. While not common - it does happen occasionally and should not be cause for panic. When it happens - press the stop button and use a small gentle blast of CO2 fire extinguisher to douse it. There is no need to get very close to the fire - generally the box 'fills' up with the CO2 gas which is heavier than air - esp. when things are not yet hot. Note this in the logbook (both so we can replace the CO2 and because of soot on the lens). Don't forget to report any fire to the Mailing List.

In the unlikely event that you cannot contain the fire with CO2 - switch to the powder extinguisher. Do not use water (risk of electrical shock). If you use the real (sealed) extinguisher - post an incident follow the accident/reporting protocol - to comply with fire, health and safety regulation.

If you are unfamiliar with fire extinguishers - and why there are many type - then read the instructions on both the CO2 and the ABC extinguisher (http://en.wikipedia.org/wiki/Fire_extinguisher) as to understand the difference.

Logging use

  • Please log your Laser Cutter use in the Lasercutter logbook.
    • This is used to track how long the tube lasts, schedule maintenance, and keep an eye on any developing issues.
    • The time you have used the laser for is shown on the machine's display panel.

Switching off & shutting down

  • Put money in the box proportional to the amount of time you used (price displayed on sign next to machine).
  • Shutdown the computer from the start button on the desktop.
  • Clear any cutting debris from the laser cutter to help the next user and the maintainers.
  • Close the lid, turn off using the key, remove your card.

What to do with Scraps

You can either make some LaserCut Mechano with the scrap (files here: C:\Documents and Settings\Hackspace\My Documents\LaserCutMechano), put the scrap into the container on the right hand side of the lasercutter or, if the piece is too small to be useful, the 'landfill' bin in the workshop.

Chlorine Testing and Material Safety

Don't cut materials that release chlorine or cyanide, or catch fire! (See Rule 0) For various information about safe and unsafe materials, please see the ATX Hackspace Laser Cutter Materials, and potentially Materials for laser cutters.

Chlorine is a very dangerous gas used in the creation of many plastics (e.g. PVC) these are safe until heated; when they release the chlorine gas. The laser cutter will easily heat plastics enough to release chlorine, which will damage the internals of the laser cutter.

To test an unknown plastic for chlorine content try the following:

  1. Heat some copper (wire's easiest) until red hot (do this for a while to remove any PVC that may be stuck to the wire from the coating).
  2. Apply red hot copper to plastic so that it melts a little onto it.
  3. Heat copper wire until red hot again.
  4. A green flame means that the plastic contains chlorine so do not use it.