Equipment/DrillPress: Difference between revisions
m (→Log) |
No edit summary |
||
| Line 5: | Line 5: | ||
|category=Equipment <!-- Main category. Please leave alone to keep item in this category --> | |category=Equipment <!-- Main category. Please leave alone to keep item in this category --> | ||
|subcat=Fabrication <!-- Sub-category if one exists. Please check main listing to see other categories contained within the main one --> | |subcat=Fabrication <!-- Sub-category if one exists. Please check main listing to see other categories contained within the main one --> | ||
|status= | |status=Working order<!-- Set to one of; Good working order, Faulty, Out of order, Under construction, Out of consumables, Scrapped, or Unknown --> | ||
|consumables=oil, cutting fluid,drive belt<!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. --> | |consumables=oil, cutting fluid,drive belt<!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. --> | ||
|accessories=Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> | |accessories=Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> | ||
| Line 18: | Line 18: | ||
}} | }} | ||
==Status== | ==Status== | ||
'''Works, but is not very precise!''' | |||
Quill run out is approximately 0.010mm - should be <0.002mm. Chuck runout is anything up to 10x this. Your holes may be oval! | Quill run out is approximately 0.010mm - should be <0.002mm. Chuck runout is anything up to 10x this. Your holes may be oval! | ||
Revision as of 17:45, 9 August 2013
| Drill press | |
|---|---|
 | |
| Model | Axminster ED16SB |
| Sub-category | Fabrication |
| Status | Working order |
| Consumables | oil, cutting fluid,drive belt |
| Accessories | Unknown |
| Training requirement | No |
| Training link | Unknown |
| ACnode | No |
| Owner | LHS |
| Origin | Unknown |
| Location | Basement, workshop |
| Maintainers | sjrapid |
Status
Works, but is not very precise!
Quill run out is approximately 0.010mm - should be <0.002mm. Chuck runout is anything up to 10x this. Your holes may be oval!
9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out with a dial indicator. Also tested with a new certified chuck and arbour (0.0012 TIR). Measured run out of about 0.25mm on the new chuck. TIR not measured on the existing keyless chuck.
We now have a drill press. The keyless chuck only goes down to 2.7 mm, so we need to get a "pin chuck". Russsss found one at the Crystal Palace workshop apparently, but I don't know where it is.
Or you can use the Dremel and mini-mill for high speed / light duty / precision stuff, and this one for everything else.
Ideal jobs :
Dremel
- High speed, tiny bits e.g. PCB drilling
Mini-Mill
- Milling plastic, small aluminium etc.
- Drilling jobs requiring accurate positioning - use the table positioning
Drill Press
- Most general purpose drilling jobs
Model
- Make: Axminster
- Model: ED16SB
- Manual: on the Axminster website
Pictures
Log
- <lovelace_> The chuck for the new stand drill falls out easily
- <lovelace_> I can't see how it tightens up
- <artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard.
- <artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely
- <lovelace_> K, seems firmly in now
- 9 Aug 2013 - sjrapid and will took the arbour and chuck off, and tested the quill run out with a dial indicator. Also tested with a new certified chuck and arbour (0.0012 TIR). Measured run out of about 0.25mm on the new chuck. TIR not measured on the existing keyless chuck.
