Difference between revisions of "Equipment/Boxford CNC Mill"
Jump to navigation
Jump to search
(Added a troubleshooting section) |
|||
Line 15: | Line 15: | ||
== Specs == | == Specs == | ||
− | * | + | * 8 spindle speeds 350 to 3500 rpm |
− | *Rapid traverse rate at 100% 2000mm/min (78"/min) | + | * Rapid traverse rate at 100% 2000mm/min (78"/min) |
* Axis travel | * Axis travel | ||
**X(longitudinal) 225mm (8.9") | **X(longitudinal) 225mm (8.9") | ||
Line 39: | Line 39: | ||
* Possible [http://tturkyilmaz.home.anadolu.edu.tr/dersler/telatturkyilmaz/programlar/cnc/millcamakz/millcam.pdf manual source] | * Possible [http://tturkyilmaz.home.anadolu.edu.tr/dersler/telatturkyilmaz/programlar/cnc/millcamakz/millcam.pdf manual source] | ||
* [https://www.dropbox.com/sc/spdovog4s2hx1ok/AACv7oagwMJUceJKUE5AU_lDa Photos] by Russ | * [https://www.dropbox.com/sc/spdovog4s2hx1ok/AACv7oagwMJUceJKUE5AU_lDa Photos] by Russ | ||
− | |||
== Needed == | == Needed == | ||
Line 53: | Line 52: | ||
* People who take it apart and leave it in pieces | * People who take it apart and leave it in pieces | ||
* Experimenting carelessly. Consider it in the same light as the laser cutter, the robot arm etc. : if you want to work on it, join the official maintainers group and cooperate. | * Experimenting carelessly. Consider it in the same light as the laser cutter, the robot arm etc. : if you want to work on it, join the official maintainers group and cooperate. | ||
+ | |||
+ | == Troubleshooting == | ||
+ | * The cutter appears to spin off-centre | ||
+ | ** When slotting in the collet make sure to put it the right way in as it's got a notch which will only go in fully when aligned |
Revision as of 14:38, 13 July 2014
CNC Mill | |
---|---|
Model | Boxford 190VMC |
Sub-category | CNC |
Status | Under construction |
Training requirement | yes |
Owner | tgreer |
Origin | Donation through tgreer |
Location | Basement, Robotics/CNC area |
Maintainers | artag, mentar |
Specs
- 8 spindle speeds 350 to 3500 rpm
- Rapid traverse rate at 100% 2000mm/min (78"/min)
- Axis travel
- X(longitudinal) 225mm (8.9")
- Y(cross) 150mm (5.9")
- Z(vertical) 140mm(5.5")
- System resolution 0.005mm
- Table dimensions 410 x 130mm(16.1" x 5.1")
- Spindle to table 202mm (7.9")
- Centre line of spindle to column 130mm (5.1")
- Table to column 5 to 130mm (0.2" x 5.1")
- Tee slots 2 x 10mm
Updates
- 10-JUL-2014 : Mill arrived, mechanics and electrics work, has what looks like a parallel pot out the back, need to research how to interface.
- 12-JUL-2014 : Connector is DB25 and almost certainly serial. It appears there is an internal g-code interpreter.
More info
- (Mailing list post)
- Spindle taper is a Coventry quick-change ref Or possibly EasyChange. maker examples
- Reliable Manual source (cheaper would be nice)
- Possible manual source
- Photos by Russ
Needed
- A base/stand (ideally, a sturdy cupboard or machine cabinet like this
- More toolholders
- Investigate g-code generation software and the interface
- Further manuals or other information
Not needed
- People who take it apart and leave it in pieces
- Experimenting carelessly. Consider it in the same light as the laser cutter, the robot arm etc. : if you want to work on it, join the official maintainers group and cooperate.
Troubleshooting
- The cutter appears to spin off-centre
- When slotting in the collet make sure to put it the right way in as it's got a notch which will only go in fully when aligned