Project:Tool Access Control/Deployment
From London Hackspace Wiki
This page is for keeping track of what we need to achieve, and how far along we are to achieving it.
Tools
| node id | name | battery backup | lock type | RFID module | PCB | PSU | MAC Address | IPv4 Addr | Status | Notes | Card cache | MQTT Topic Base | Software Door release |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | back doorbot | 7Ah SLA | Gianni EB300 solenoid bolt | Elechouse NFC module v3 | acnode/doorbot board | in enclosure, mains fed | 00:1a:b6:03:03:47 | In Service | RAM | /door/gf-back | Installed and active | ||
| 3 | LulzBot_Hull | nil | n/a | Elechouse NFC module v4 | wire wrap | in enclosure, wall wart | 00:1A:B6:02:B2:18 | 10.0.40.3 | In Service | SSR | eeprom | /tool/hull | |
| 4 | LulzBot_Crump | nil | n/a | Elechouse NFC module v3 | acnode board rev 2 | in enclosure, wall wart | 00:1A:B6:02:BF:6F | 10.0.40.4 | In Service | SSR in tool itself | eeprom | /tool/crump | |
| 5 | Ground floor doorbot | 7Ah SLA | Gianni EB300 solenoid bolt | Elechouse NFC module v4 | acnode shield rev 4, also acnode board rev 2 for pinouts | 00:1A:B6:02:F3:F5 | 10.0.40.5 | In Service | built into same enclosure as Front Doorbot. RFID reader to be placed on glass door | RAM | /door/gf-front-inner | Installed and active | |
| 6 | Front doorbot | 7Ah SLA | landlord's maglock, remote relay release | Deek-Robot | acnode shield rev 4, also acnode board rev 2 for pinouts | 00:1A:B6:03:12:F4 | 10.0.40.6 | In Service | Landlord's maglock, powered by landlord's PSU, installed relay to interrupt. Door release is Landlord's, with timed release via their door entry system | RAM | /door/gf-front-external | N/A - landlord's door release | |
| 8 | Biolab restricted doorbot | 7Ah SLA | Elechouse NFC module v4 | acnode shield rev 4, also acnode board rev 2 for pinouts | 90:A2:DA:00:F3:C3 | 10.0.40.8 | In Service | Shared enclosure and PSU with back gate cage doorbot | RAM | /door/gf-biolab | Installed and active | ||
| 10 | Radio room restricted doorbot | 7AH SLA | maglock | Deek-Robot | acnode shield rev 4, also acnode board rev 2 for pinouts | in enclosure | 00:1A:B6:03:44:BF | In Service | in same enclosure as Electronics Room doorbot | RAM | /door/1f-funk (because "radio" is cooler in german) | Installed and active | |
| 11 | lasercutter | nil | n/a | Elechouse NFC module v4 | acnode board rev 2 | POE splitter | 00:1A:B6:02:CB:75 | 10.0.40.11 | In Service | SSR in acnode enclosure | eeprom | /tool/laz0rz | |
| 12 | Back gate cage doorbot | maglock | Elechouse NFC module v4 | acnode/doorbot board | 00:1a:b6:02:d9:4b | 10.0.40.12 | In Service | Shared enclosure and PSU with biolab doorbot | sdcard | /door/gf-backgate | Installed and active | ||
| 13 | Hopper | nil | n/a | LHS vending machine board | Vending Machine. Under construction | Neither door, nor tool, registered in acserver as a door | n/a | ||||||
| 14 | SSR only ready for deployment | nil | acnode board rev 2 | single phase AC | |||||||||
| 15 | Colchester Master Lathe | nil | n/a | Deek-Robot | acnode/doorbot board | POE splitter | 00:1a:b6:03:41:51 | 10.0.40.15 | In Service | 3-phase but possible single phase low-current control cable numbers 22/23 | eeprom | /tool/colchester | |
| 16 | Bridgeport Mill | nil | n/a | Deek-Robot | acnode/doorbot board | POE splitter | 00:1A:B6:03:41:4A | 10.0.40.16 | In Service | Interrupts 110V power to e-stop circuit. acnode powered via PoE | eeprom | /tool/bridgeport | |
| 17 | Tool Store | 7Ah SLA | maglock | Elechouse NFC module v4 | acnode/doorbot board | in enclosure | 00:1A:B6:03:52:70 | 10.0.40.17 | In Service | built into same enclosure as back doorbot | /door/gf-toolstore | ||
| 18 | Sedgwick TA315 Table Saw | nil | n/a | Elechouse NFC module v4 | acnode board rev 2 | 00:1A:B6:02:CD:98 | 10.0.40.18 | In Service | single phase AC. 16A commando | /tool/sedgwick | |||
| Wishlist for acnode/doorbot controlled equipment below here | |||||||||||||
| De Walt Table Saw | single phase AC. SSR | ||||||||||||
| Woodworking lathe | single phase AC, 13A | ||||||||||||
| 19 | Planer | nil | n/a | Deek-Robot | acnode board rev 2 | 00:1a:b6:02:cc:d9 | 10.0.40.19 | In Service | single phase 16A. SSR | ||||
| 20 | Radial Arm Saw | nil | n/a | acnode shield rev 4 | 00:1A:B6:03:08:0A | /tool/ras |
If an acnode crashes and is fed by PoE, then try unplugging the network cable and re-plugging it. The indicator LED on the button should rainbow cycle while rebooting.
Items in stock
- 0x Connected Launchpads
- 3x 40A SSRs
- 3x RFID Readers
- 0x RGB LED arcade buttons
