Project:Tool Access Control/Deployment
< Project:Tool Access Control
Jump to navigation
Jump to search
Revision as of 16:28, 15 October 2020 by Simon Hewison (talk | contribs) (update from spreadsheet, the old page was way out of date)
This page is for keeping track of what we need to achieve, and how far along we are to achieving it.
Tools
node id | name | battery backup | lock type | RFID module | PCB | PSU | MAC Address | IPv4 Addr | Status | Notes | Card cache | MQTT Topic Base | Software Door release |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | back doorbot | 7Ah SLA | Gianni EB300 solenoid bolt | Elechouse NFC module v3 | acnode/doorbot board | in enclosure, mains fed | 00:1a:b6:03:03:47 | In Service | RAM | /door/gf-back | Installed and active | ||
3 | LulzBot_Hull | nil | n/a | Elechouse NFC module v4 | wire wrap | in enclosure, wall wart | 00:1A:B6:02:B2:18 | 10.0.40.3 | In Service | SSR | eeprom | /tool/hull | |
4 | LulzBot_Crump | nil | n/a | Elechouse NFC module v3 | acnode board rev 2 | in enclosure, wall wart | 00:1A:B6:02:BF:6F | 10.0.40.4 | In Service | SSR in tool itself | eeprom | /tool/crump | |
5 | Ground floor doorbot | 7Ah SLA | Gianni EB300 solenoid bolt | Elechouse NFC module v4 | acnode shield rev 4, also acnode board rev 2 for pinouts | 00:1A:B6:02:F3:F5 | 10.0.40.5 | In Service | built into same enclosure as Front Doorbot. RFID reader to be placed on glass door | RAM | /door/gf-front-inner | Installed and active | |
6 | Front doorbot | 7Ah SLA | landlord's maglock, remote relay release | Deek-Robot | acnode shield rev 4, also acnode board rev 2 for pinouts | 00:1A:B6:03:12:F4 | 10.0.40.6 | In Service | Landlord's maglock, powered by landlord's PSU, installed relay to interrupt. Door release is Landlord's, with timed release via their door entry system | RAM | /door/gf-front-external | N/A - landlord's door release | |
8 | Biolab restricted doorbot | 7Ah SLA | Elechouse NFC module v4 | acnode shield rev 4, also acnode board rev 2 for pinouts | 90:A2:DA:00:F3:C3 | 10.0.40.8 | In Service | Shared enclosure and PSU with back gate cage doorbot | RAM | /door/gf-biolab | Installed and active | ||
10 | Radio room restricted doorbot | 7AH SLA | maglock | Deek-Robot | acnode shield rev 4, also acnode board rev 2 for pinouts | in enclosure | 00:1A:B6:03:44:BF | In Service | in same enclosure as Electronics Room doorbot | RAM | /door/1f-funk (because "radio" is cooler in german) | Installed and active | |
11 | lasercutter | nil | n/a | Elechouse NFC module v4 | acnode board rev 2 | POE splitter | 00:1A:B6:02:CB:75 | 10.0.40.11 | In Service | SSR in acnode enclosure | eeprom | /tool/laz0rz | |
12 | Back gate cage doorbot | maglock | Elechouse NFC module v4 | acnode/doorbot board | 00:1a:b6:02:d9:4b | 10.0.40.12 | In Service | Shared enclosure and PSU with biolab doorbot | sdcard | /door/gf-backgate | Installed and active | ||
13 | Hopper | nil | n/a | LHS vending machine board | Vending Machine. Under construction | Neither door, nor tool, registered in acserver as a door | n/a | ||||||
14 | SSR only ready for deployment | nil | acnode board rev 2 | single phase AC | |||||||||
15 | Colchester Master Lathe | nil | n/a | Deek-Robot | acnode/doorbot board | POE splitter | 00:1a:b6:03:41:51 | 10.0.40.15 | In Service | 3-phase but possible single phase low-current control cable numbers 22/23 | eeprom | /tool/colchester | |
16 | Bridgeport Mill | nil | n/a | Deek-Robot | acnode/doorbot board | POE splitter | 00:1A:B6:03:41:4A | 10.0.40.16 | In Service | Interrupts 110V power to e-stop circuit. acnode powered via PoE | eeprom | /tool/bridgeport | |
17 | Tool Store | 7Ah SLA | maglock | Elechouse NFC module v4 | acnode/doorbot board | in enclosure | 00:1A:B6:03:52:70 | 10.0.40.17 | In Service | built into same enclosure as back doorbot | /door/gf-toolstore | ||
18 | Sedgwick TA315 Table Saw | nil | n/a | Elechouse NFC module v4 | acnode board rev 2 | 00:1A:B6:02:CD:98 | 10.0.40.18 | In Service | single phase AC. 16A commando | /tool/sedgwick | |||
Wishlist for acnode/doorbot controlled equipment below here | |||||||||||||
De Walt Table Saw | single phase AC. SSR | ||||||||||||
Woodworking lathe | single phase AC, 13A | ||||||||||||
19 | Planer | nil | n/a | Deek-Robot | acnode board rev 2 | 00:1a:b6:02:cc:d9 | 10.0.40.19 | In Service | single phase 16A. SSR | ||||
20 | Radial Arm Saw | nil | n/a | acnode shield rev 4 | 00:1A:B6:03:08:0A | /tool/ras |
If an acnode crashes and is fed by PoE, then try unplugging the network cable and re-plugging it. The indicator LED on the button should rainbow cycle while rebooting.
Items in stock
- 0x Connected Launchpads
- 3x 40A SSRs
- 3x RFID Readers
- 0x RGB LED arcade buttons