Difference between revisions of "Equipment/DrillPress"
Jump to navigation
Jump to search
m |
|||
| Line 6: | Line 6: | ||
|subcat=Fabrication <!-- Sub-category if one exists. Please check main listing to see other categories contained within the main one --> | |subcat=Fabrication <!-- Sub-category if one exists. Please check main listing to see other categories contained within the main one --> | ||
|status=Good working order<!-- Set to one of; Good working order, Faulty, Out of order, Under construction, Out of consumables, Scrapped, or Unknown --> | |status=Good working order<!-- Set to one of; Good working order, Faulty, Out of order, Under construction, Out of consumables, Scrapped, or Unknown --> | ||
| − | |consumables=oil, cutting fluid <!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. --> | + | |consumables=oil, cutting fluid,drive belt<!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. --> |
|accessories=Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> | |accessories=Unknown <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. --> | ||
|reqtraining=No<!-- Is training required to use this equipment? Yes or no. --> | |reqtraining=No<!-- Is training required to use this equipment? Yes or no. --> | ||
| Line 51: | Line 51: | ||
#<artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard. | #<artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard. | ||
#<artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely | #<artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely | ||
| − | |||
#<lovelace_> K, seems firmly in now | #<lovelace_> K, seems firmly in now | ||
| − | |||
Revision as of 11:33, 2 August 2013
| Drill press | |
|---|---|
 | |
| Model | Axminster ED16SB |
| Sub-category | Fabrication |
| Status | Good working order |
| Consumables | oil, cutting fluid,drive belt |
| Accessories | Unknown |
| Training requirement | No |
| Training link | Unknown |
| ACnode | No |
| Owner | LHS |
| Origin | Unknown |
| Location | Basement, workshop |
| Maintainers | sjrapid |
Status
We now have a drill press. The keyless chuck only goes down to 2.7 mm, so we need to get a "pin chuck". Russsss found one at the Crystal Palace workshop apparently, but I don't know where it is.
Or you can use the Dremel and mini-mill for high speed / light duty / precision stuff, and this one for everything else.
Ideal jobs :
Dremel
- High speed, tiny bits e.g. PCB drilling
Mini-Mill
- Milling plastic, small aluminium etc.
- Drilling jobs requiring accurate positioning - use the table positioning
Drill Press
- Most general purpose drilling jobs
Model
- Make: Axminster
- Model: ED16SB
- Manual: on the Axminster website
Pictures
Log
- <lovelace_> The chuck for the new stand drill falls out easily
- <lovelace_> I can't see how it tightens up
- <artag> it should be a taper. Assuming it's clean (not got anticorrosion varnish on it) then it should want a good fast whack up into the quill. Not with a hammer - just push it fast, by hand. Use the momentmum of the chuck to get it in hard.
- <artag> if there's a screw thread in the end of the taper thrn it can use a drawbar like the 3-in-1 but that's fairly unlikely
- <lovelace_> K, seems firmly in now