Search results

• Door control system
  ...make a noise, should there be a need for it. In the same enclosure as the Electronics Lab doorbot. SLA 12V backup battery. Restricted access. You need to have ...he door (with a timed release), will also use another contact to break the circuit that would hold the door closed while the button is pressed.
  16 KB (2,795 words) - 15:27, 5 November 2022
• Basic Electronics Course
  ==== 2012 : Basic Electronics Course ==== There's an interest in some basic electronics courses, taught by volunteer members to other members.
  1 KB (165 words) - 19:28, 8 May 2013
• Not Just Arduino-talks
  ...are a few examples of topics about power control and design in low voltage circuits, I'm sure some of them overlap. Feel free to add more talks and leave some |The mathematics of electronics, Watts, Ohms, Farads, Coulombs, Amperes, Volts || || |Paul Maidment, [[U
  3 KB (470 words) - 21:28, 15 January 2014
• Workshops/Arduino for beginners 2
  ...starter kit courtesy of [http://www.earthshineelectronics.com/ Earthshine Electronics]. Prior Knowledge of electronics is not needed, just a desire to learn.
  2 KB (270 words) - 18:07, 8 May 2013
• 447 Power
  ...n to stop using these circuits, with the exception of the ceiling lighting circuits. ...main board, all using circuit breakers (MCBs) with RCD protection on most circuits. The status of all of the breakers can be seen without opening the units.
  8 KB (1,206 words) - 18:52, 21 October 2021
• Project:ETextiles
  So far I have worked out how to do this electronically. ...uit design. It's all insulated wire so there won't be a huge risk of short circuits.
  1 KB (256 words) - 23:32, 29 June 2011
• Project:25-hpamakers-reprap
  ====2-Electronics==== (Sam) Check Wiring + Firmware: Desktop-based test of all stepper motors and electronics.
  5 KB (692 words) - 23:56, 28 May 2013
• Project:PCB Making
  How to make a Printed Circuit Board (PCB) using photoresist laminates. Once an electronic prototype is working on a breadboard, the next logical step is to firm up
  14 KB (2,214 words) - 21:13, 15 June 2014
• Project:Classroom HackSpaceChallenge
  ===Electronics=== ===Electronics===
  4 KB (605 words) - 15:03, 3 June 2013
• Classroom HackSpaceChallenge/Report/1
  ...advanced robot sent from the future for turning pizza, chips and Cola into circuit boards and lulz. ...e day this chemist wandered into the hack space, a lair of programmers and electronics geeks. So far he has managed not to arouse the suspicion of the natives.
  4 KB (737 words) - 11:39, 25 March 2011
• Workshops/Arduino for beginners/Planning
  *makers/artists who want to add electronics to their interactive exhibit ...t with a general overview of hacking with respect to art, home automation, circuit bending, etc, presented as a short lecture to introduce the arduino and sim
  5 KB (749 words) - 18:08, 8 May 2013
• Project:Cupcake-o-Matic
  ===Updating the Electronics=== ...lly came with the RepRap [http://reprap.org/wiki/Generation_3 Generation 3 Electronics] set:
  14 KB (2,609 words) - 02:17, 8 November 2012
• Equipment/Farnell TSV70
  |location=Ground Floor, Electronics area<!-- Floor, room/zone and location within that area --> ...n it's actually putting out 50V etc. '''Be careful''', or you may fry your circuit sooner than you intended.
  2 KB (403 words) - 19:06, 14 February 2018
• Pledge: Nanodes/Details
  Early boards were produced by Spirit Circuits, lightish green in colour with the distinctive Hackspace logo. Later board Nanodes 0520 - 0539 20 for Earthshine Electronics (UK Reseller)
  83 KB (9,948 words) - 09:34, 16 May 2013
• JobBoard
  ...e looking for someone ideally London-based and experienced in RF/microwave circuit design. No ultrasonics experience is necessary, but it's nice to have. Part == Electronic and Firmware Engineer at Tech Will Save Us==
  26 KB (4,111 words) - 15:29, 30 July 2019
• Public Relations
  etc. A storage room, and a nice clean work shop for electronics and desk electronics, small things will come from the subscriptions, but larger
  8 KB (1,367 words) - 01:10, 29 May 2013
• User:Larz
  === Modify ESC-Electronic Speed Controller === === ''High Power Rocketry Electronics <small>(telemetry, staging, recovery deployment)</small>'' ===
  5 KB (810 words) - 09:09, 30 June 2012
• Project:Nanode/News
  ...d worldwide. Nanode boards can easily be soldered by absolute beginners in electronics. ...ode Version 5, built up on the rather funky free "Naked" board from Spirit Circuits. I have to admit that from an advertising perspective - this campaign by
  26 KB (4,312 words) - 19:20, 7 November 2011
• Project:HSRDP
  * [[Project:UMI_RTX_Robot_arm|Robot arm]] electronics replaced and working, need current feedback and control lines added. * The drive train electronics are ready, they need to be installed together with the steering motor mo
  7 KB (1,044 words) - 11:49, 19 January 2016
• Project:UMI RTX Robot arm
  ...ell and an Arduino ofcourse)! :D But if someone wants to restore the stock electronics I will avoid hacking the old control board up in-case you want to have a ...which ones died, you might be able to ignore this (once they've burnt open-circuit) but it would be best to replace the lot. There are about 4 1uF 35V, about
  11 KB (1,858 words) - 22:23, 7 March 2016

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)