147
edits
Prusa/Parts List: Difference between revisions
From London Hackspace Wiki
no edit summary
Billy Smith (talk | contribs) No edit summary |
Billy Smith (talk | contribs) No edit summary |
||
| Line 7: | Line 7: | ||
If you want to provide the parts that we don't have yet, add your name to the volunteer section for the part, and go for it. There are links to the order pages for a couple of supplier's websites, but if you find one that we haven't looked at yet, then add them in. | If you want to provide the parts that we don't have yet, add your name to the volunteer section for the part, and go for it. There are links to the order pages for a couple of supplier's websites, but if you find one that we haven't looked at yet, then add them in. | ||
If a part doesn't have a name attached, then it's one that we still need.. | If a part doesn't have a name attached, then it's one that we still need... | ||
This parts list is partially copied from here, http://reprap.org/wiki/Prusa_Mendel#Bill_of_Materials with adaptations for the difference in the design used. Any references to the Sections in the Build Manual, are based on this document, http://reprap.org/wiki/Prusa_Mendel_Build_Manual | |||
| Line 120: | Line 122: | ||
</tr> | </tr> | ||
</table> | </table> | ||
== Non-Printed Parts == | |||
<table border="1" cellpadding="1" cellspacing="1" width="100%"> | |||
<tr> | |||
<td>'''Quantity'''</td> | |||
<td>'''Description'''</td> | |||
<td>'''Type'''</td> | |||
<td>'''Comments'''</td> | |||
<td>'''Volunteer'''</td> | |||
</tr> | |||
<tr> | |||
<td>83</td> | |||
<td>M8 nut</td> | |||
<td>Fastener</td> | |||
<td>100 pack for £2.50 - Clerkenwell Screws.</td> | |||
<td>Billy</td> | |||
</tr> | |||
<tr> | |||
<td>93</td> | |||
<td>M8 washer</td> | |||
<td>Fastener</td> | |||
<td>100 pack for £2.50 - Clerkenwell Screws.</td> | |||
<td>Billy</td> | |||
</tr> | |||
<tr> | |||
<td>6</td> | |||
<td>M8*30 mudguard / fender washer</td> | |||
<td>Fastener</td> | |||
<td>These are also known as penny washers, they have a much larger outer diameter than regular washers. Salvaged from the random screws box in the workshop.</td> | |||
<td>Billy</td> | |||
</tr> | |||
<tr> | |||
<td>2</td> | |||
<td>M4×20 bolt</td> | |||
<td>Fastener</td> | |||
<td>To mount the extruder</td> | |||
<td></td> | |||
</tr> | |||
<tr> | |||
<td>2</td> | |||
<td>M4 nut</td> | |||
<td>Fastener</td> | |||
<td>To mount the extruder</td> | |||
<td></td> | |||
</tr> | |||
<tr> | |||
<td>2</td> | |||
<td>M4 washer</td> | |||
<td>Fastener</td> | |||
<td>To mount the extruder</td> | |||
<td></td> | |||
</tr> | |||
<tr> | |||
<td>22</td> | |||
<td>M3×10 bolt</td> | |||
<td>Fastener</td> | |||
<td></td> | |||
<td></td> | |||
</tr> | |||
<tr> | |||
<td>16</td> | |||
<td>M3×25 bolt</td> | |||
<td>Fastener</td> | |||
<td>Or eight M3×25 bolt plus eight M3x20 bolts. The M3x25 bolts are too long for the recent Prusa z-motor-holder and rod-clamp, and also for the Z motor couplings. See Section 8, steps 4 and 13 for details.</td> | |||
<td></td> | |||
</tr> | |||
</table> | |||
16 M3×25 bolt Fastener Or eight M3×25 bolt plus eight M3x20 bolts. The M3x25 bolts are too long for the recent Prusa z-motor-holder and rod-clamp, and also for the Z motor couplings. See Section 8, steps 4 and 13 for details. | |||
4 M3×40 bolt Fastener | |||
70 M3 washer Fastener | |||
40 M3 nut Fastener 8 optionally locknut / stop nut / nyloc | |||
2 M3 grub screw / set screw Fastener M3x8 seems about ideal but anything 6mm or longer should do. If these are hard to get, additional M3×10 bolts will do the job instead. | |||
3 608 roller skate / inline skate / skateboard bearing Bearings You don't need to ask for a "608 bearing" at a skate shop, just ask for wheel bearings. | |||
4 ballpoint pen springs Spring To fit over M3 bolts. Ballpoint pens are a common, cheap source of suitable springs. They are about 25mm long and compress to about 10mm. | |||
6 M8×370mm Threaded rod 3 per side | |||
Note: The threaded rods can be cut from larger 6x1m pieces (see Threaded Rod Cut Order below). | |||
4 M8×294mm Threaded rod front / rear | |||
3 M8×440mm Threaded rod top / bottom | |||
2 M8×210mm Threaded rod Z-leadscrew | |||
1 M8×50mm Threaded rod or M8x30 or longer bolt for X idler. Take care: if the bolt is too long, it may not be threaded along a sufficient length | |||
2 8mm×420mm Smooth rod X-bar | |||
Note: 304 Stainless Steel, A2 Tool Steel, or O1 Tool Steel are recommended for smooth rods as it can help to prevent friction from rust and manufacturing (straightness) standards are higher. Rust issues can be prevented on the normal steel rods by maintaining a coat of oil. The smooth rods can also be cut from larger 3x1m pieces (see Smooth Rod Cut Order below). | |||
2 8mm×406mm Smooth rod Y-bar | |||
2 8mm×350mm Smooth rod Z-bar | |||
1 225mm×225mm print top plate Thick Sheet | |||
1 140mm×225mm print bottom plate Thick Sheet Note: The Prusa Iteration 2 design does not use a print bottom plate. | |||
1 840mm×5mm T5 pitch timing belt Belt Y axis | |||
1 900mm×5mm T5 pitch timing belt Belt X axis | |||
5 NEMA 17 bipolar stepper motor Stepper Be sure to get ones with at least 20mm of shaft length. Shorter shafts require modifications to the X pulley assembly and Z motor couplers. One of the five motors, for use with the extruder, should be capable of creating a holding torque of at least 40Ncm, at the very least. | |||
---- | |||
---- | ---- | ||
