Components

The Hackspace carries a range of electronic (and other) components in stock. As a rule, members can use anything for free, as long as the cost is less than £1. However, if you're using more than £5-£10 worth of components a month, we'd appreciate a donation to cover those costs.

Purchasing

Please include a link to the item, preferably from Farnell, or it won't be ordered.

If you're a member of the space we'll happily order components for you and take advantage of bulk discounts/free shipping. If the component you request is cheap, we may order more than you need and bring it into stock in the space (if that's the case, then it's free as above).

Requests

• 10 AA batteries for the label printers. E.g. pack of 40 for £17
• NPN transistors (running low), atm we stock BC547BG
• 16MHz crystals (farnell)
• Arduinos (we should probably get these from Earthshine, but our budget is a bit tight to stretch to them currently -Russ)
• Miniature trimming potentiometers
  • 10K
  • 100K
  • I have put a selection of multiturn trimpots in a translucent plastic compartment box, currently on top of the component drawers in the main room - artag.
• 4093 (four NAND Schmitt Triggers in one chip, useful for e.g. polyphonic square wave oscillators) (now UK stock)
• 4017B ("decade counter"/10-step counter, useful for sequencers) (now UK stock)
• 4050N level shifter
• MCP23008 I²C IO expander
• 555 and 556 timers. These are generally useful, we should always keep a few in stock.
• Socket cap screws, nuts, washers:
  • M3X10 x 100
  • M3X16 x 100
  • M3X20 x 100
  • M3X25 x 100
  • M3X30 x 100
  • M3 nut x 100 x 6
  • M3 washer x 100 x 5
  • M3 spring washer x 100 x 1
• General box of various M2-M10 nuts, bolts and washers. (RS Components)
  • 650 piece nylon metric nut kit
  • 600 piece nylon metric screw kit
  • A4 stainless steel metric full nut kit
  • A2 stainless steel metric full nut kit
  • ISO metric ZnPt steel machine screw kit
• Capacitors:
  • 22pF
  • 0.1µF
  • 0.22µF
  • 0.39µF
  • 0.47µF
  • 1µF (small)
  • 2.2µF
  • 10µF
  • 22µF
  • 100µF
  • 220µF
• Tools:
  • Cheap multimeter (eBay)
  • Wire cutters
• Prototyping:
  • Jumper wires (eBay) - the ones we have are running low and are not the easiest to insert.
  • Spot face cutter
  • Breadboard (Rapid)
  • Banana leads (Rapid)

Personal requests

Alex:

• Decade counter ICs x 2
• Hex inverting Schmitt trigger ICs x2

AntLoom

• OPTOCOUPLER x 2, 43p
• OPTOCOUPLER, Z-X x2, 124p
• NXP - BT136-600 - TRIAC, 4A, 600V, TO-220 x2, 65p

Links Needed

Please help by finding an appropriate link for the following.

• new tips for the general soldering irons! (Not at space so can't check models, if this matters)
• "brass sponge" for cleaning soldering iron tips.
• A couple of stiff brushes - to make cleanup around MIll and Lathe easier. Perhaps with some chain to tie them to the table.
• LEDs (varying, some good bright ones) +1 (we have loads of basic red/green/yellow etc ones)
• 12V 3A solid-state relay
• solid-core cable (RGBYKW) and multicore
  • I have some reels of wire (stranded and coax - none solid) to bring in so stick to stocking up on solid for now - artag

Tools and equipment

See the Wishlist page.

Some tools we could regard as consumables; get cheap ones and replace them frequently. E.g.:

• screw drivers

Tool bits and pieces

Recently retired/thrown away

• spade-drills which had side of the spade drill broken sized 8, 10, 12 and 22 (2011/04)
• Down to the last hacksaw iron blade (2011/04) - 410 length
• Down to the last Pendulum Jigsaw saws of the non-T shape saws (2011/04)

Consumables

We're running low on:

• Logic chips. I think the 74HCT series is a reasonable place to start, but I'm not an expert here.
• Some banaplugs or already wired up banaplug wires in the usual colours and length.

See also: Inventory#Stocked components.