Project:USB Disco Dance Floor/v1: Difference between revisions
(Added image of MIT 1E disco dance floor, as an example of what I aim to accomplish.) |
(Added link to USB hub chip) |
||
| Line 36: | Line 36: | ||
[[File:Ddf-ddr-concept.gif|thumb|right|Dance Dance Revolution/Guitar Hero mashup concept]] | [[File:Ddf-ddr-concept.gif|thumb|right|Dance Dance Revolution/Guitar Hero mashup concept]] | ||
[[{{#titleparts:{{FULLPAGENAME}}|-1}}|Version 2]] of this project will provide RGB+UV for each cell, with pressure sensors. Ideally the pressure sensors will have a resolution of one cell, so that the floor could be used for games (e.g. Tetris or a mash-up of Dance Dance Revolution and Guitar Hero). The Arduinos (or other microcontrollers) will be embedded into the board design, and the PCBs batch-produced. | [[{{#titleparts:{{FULLPAGENAME}}|-1}}|Version 2]] of this project will provide RGB+UV for each cell, with pressure sensors. Ideally the pressure sensors will have a resolution of one cell, so that the floor could be used for games (e.g. Tetris or a mash-up of Dance Dance Revolution and Guitar Hero). The Arduinos (or other microcontrollers) will be embedded into the board design, and the PCBs batch-produced. The board will also have a [http://uk.farnell.com/texas-instruments/tusb2046bvf/ic-usb-hub-4-port-32lqfp/dp/1470507 4-port USB hub] built into it, for inter-module communication. | ||
Note: Tetris requires 10px wide by 20 high for the playing field. DDR would require ((NPlayers * 5) - 1)px wide. It looks like the floor would have to therefore be a minimum of 3x8 modules for Tetris, and probably the same for DDR (but perhaps shorter). For two players, DDR requires a minimum of 3 modules wide, but the height could be relatively variable. The example floor to the right is 3x7 modules. | Note: Tetris requires 10px wide by 20 high for the playing field. DDR would require ((NPlayers * 5) - 1)px wide. It looks like the floor would have to therefore be a minimum of 3x8 modules for Tetris, and probably the same for DDR (but perhaps shorter). For two players, DDR requires a minimum of 3 modules wide, but the height could be relatively variable. The example floor to the right is 3x7 modules. | ||
Revision as of 10:23, 7 April 2011
| USB Disco Dance Floor | |
|---|---|
| Created | 2011-03-31 |
| Version | 1 |
| Members | DMI |
| Project Status | Prototyping |
| QR code | |
Introduction
The aim of this project is to create a USB-controlled, Arudino-powered 70's-style disco dance floor, inspired by a similar project by a student at MIT. It will act as a modular, low-resolution RGB display. Each pixel will be 6-8" per side, and it will come in 4x4-pixel modules that can be connected together.
The board, firmware, and controller software will (of course) be open-sourced.
Terminology
Each pixel will be referred to as a cell, and each self-contained block of 4x4 pixels will be referred to as a module.
Construction
Prototype
The prototype is just a small bit of veroboard (in fact, slightly too small... it is one hole shorter than I really wanted!) with the traces cut between holes using a Dremel.
Materials
I plan for the main body of the module to be made of wood, with some sort of frosted/diffused acrylic top. It needs to be strong enough to handle a relatively large number of people jumping up and down on it, as well as potentially spilling drinks etc.
Project log
- 2011-03-29
-
- I am building the prototype circuit on veroboard: one 4x4 array of RGB Piranha LEDs, plus three TLC5940 drivers.
- I have yet to decide whether the ICs will be assigned one per colour or just sequentially tie the outputs to the LED pins. I should be able to get 4096 levels per output channel, so this gives me (apparently) 68.7 billion colours per pixel (4096³), which should probably be enough. I'll probably reduce that down to the more standard 256 levels.
- A quick test on breadboard showed that I can at least control one TLC5940 and 5 LEDs as expected, with a sweeping pattern across the outputs. Next stage is doing exactly the same on the veroboard prototype!
- 2011-04-03
-
- I have finished soldering the LED array onto the board, including resistors, and I have now made a start on wiring the LEDs to the controllers. I also connected all of the common anodes
- I decided to connect the LEDs to the drivers sequentially, so R0 -> OUT00, G0 -> OUT01, B1 -> OUT02, etc. This was partially prompted by designing a PCB for future use. I hope to have a prototype of the board produced professionally, so I can test and refine it. A future version of the board will have the microcontroller embedded (as described below), or possibly done as an Arduino shield. Turning it into a shield is unlikely, however: the board would be quite large, and routing might be complex. It would likely be more than my version of Eagle can handle!
Future directions
Version 2 of this project will provide RGB+UV for each cell, with pressure sensors. Ideally the pressure sensors will have a resolution of one cell, so that the floor could be used for games (e.g. Tetris or a mash-up of Dance Dance Revolution and Guitar Hero). The Arduinos (or other microcontrollers) will be embedded into the board design, and the PCBs batch-produced. The board will also have a 4-port USB hub built into it, for inter-module communication.
Note: Tetris requires 10px wide by 20 high for the playing field. DDR would require ((NPlayers * 5) - 1)px wide. It looks like the floor would have to therefore be a minimum of 3x8 modules for Tetris, and probably the same for DDR (but perhaps shorter). For two players, DDR requires a minimum of 3 modules wide, but the height could be relatively variable. The example floor to the right is 3x7 modules.
