Equipment/HPC LS3060 Laser Cutter: Difference between revisions

From London Hackspace Wiki
No edit summary
mNo edit summary
 
(262 intermediate revisions by 45 users not shown)
Line 1: Line 1:
[[File:Laser-cutter-installed.jpg|thumb|right]]
{{EquipmentInfobox
|name=Laser cutter <!-- Name of the item. -->
|image=Laser-cutter-installed.jpg <!-- Image of the item. Leave with placeholder image if none exists. -->
|model=HPC LS3060
|category=Equipment <!-- Main category. Please leave alone to keep item in this category -->
|subcat=Defunct <!-- Sub-category if one exists. Please check main listing to see other categories contained within the main one -->
|status=Unknown
|consumables=Unknown <!-- Any items used up in normal operation, such as; ink, paper, saw-blades, cutting disks, oil, etc.. -->
|accessories=Coolbot <!-- Any items associated with the equipment but not consumable, such as; drill bits, safety gloves, goggles, etc.. -->
|reqtraining=Yes <!-- Is training required to use this equipment? Yes or no. -->
|trainlink=[[Lasercutter_Training|Training Roster]] <!-- If training is required, provide a link to training signup or contact page. Otherwise leave blank. -->
|acnode=No <!-- Is the equipment ACnode locked? -->
|owner=LHS <!-- Provide a link to owners members page if other than LHS -->
|origin=Pledge <!-- If via pledge, please link to the completed pledge page on the wiki -->
|location=Ground floor, main room<!-- Floor, room/zone and location within that area -->
|maintainers=Solexious, Yetifiasco<!-- If an individual is nominated as managing the upkeep of this item, please list them here. -->
|template_ver=1.1 <!-- Please do not change. Used for tracking out-of-date templates -->
}}
'''<div style="font-weight: bold; font-size: 110%">NOTE: This is our old laser cutter which has now been replaced with the [[Silvertail A0 Laser Cutter]]. This page is left here for reference.</div>'''
 
We have a HPC LS3060 laser engraver and cutter, with a cutting area of 300mm x 560mm. Trained [[Membership | members]] can use it for the very reasonable rate of £5 per hour.
 
This cutter was sold.
 
[[File:Laser-cut-key-rings.jpg|thumb|right]]
[[File:Laser-cut-key-rings.jpg|thumb|right]]




== '''<div style="color:red">Please don't touch or fiddle with the laser cutter unless you've have been trained. </div>'''==
==Training==


You must not use the laser cutter without being trained. The laser cutter is unlikely to hurt you, but you can easily hurt '''it''' without training.


Training is given most Tuesdays at about 8pm, feel free to ask for help.  
Training is given most Wednesdays or Thursdays at around 8pm, is free to attend and available to all members but your place needs to be pre-booked. Space is strictly limited per session so you need to reserve a spot on the [[Lasercutter_Training|Training Roster]] when a session is available - watch the [[Mailing List]] for announcements. Reserving a spot is on a first come first serve so you'll need to be quick. If you can't attend your training session please remove your name from the roster and inform the Mailing List, this will save wasting people's time and can allow a last minute replacement to take your slot.
The laser cutter is unlikely to hurt you but you could easily hurt it without training.


==Status==
Training is currently limited to members only but this may change in the future.
The cutter is currently operational - check the [[Equipment/LaserCutter/LogBook|logbook]] for more information.


Cooling of the laser cutter is now fully automatic.
A good way to get notified of new training sessions is to go to the roster page, add it to your wiki page Watch list, and modify your wiki account preferences so that you receive emails when pages you Watch get modified.


We're currently trying to [[Projects/RELaserSoftware|reverse engineer]] the [[Equipment/LaserCutter/Software|software]].
Feel free to ask for help on the [[Mailing List]], but please read the [[Mailing_list_FAQ|FAQ]] first


Information about additional useful bits of software installed on the machine can be found on the [[Equipment/LaserCutter/Software|software page]].
==Costs==


==Model==
* Training - Free
* [http://hpclaser.co.uk/ HPC] LS3060 "plus" laser engraver and cutter.
* Usage - £5/hour
====Specification====
* Consumables - Bring your own and/or use what is in the off cuts bin, but always ensure (rather than assume) it's [[Laser_Cutter/Instructions#Chlorine_Testing_and_Material_Safety|laser safe]].
{| class="topalign"
| '''Laser:'''
|| 40W - water cooled CO<sub>2</sub> laser.
|-
| '''Working area:'''
||320 x 600mm honeycomb bed (cutting area possibly about 300 x 550mm)
|-
| '''Features:'''
|| Air-assist (removes debris from cutting region),
red-dot pointer (to show beam location)
|-
| '''Water cooling:'''
|| Simple tube cooling circuit connected with (9mm OD, 6mm ID) latex tube.
Uses supplied submersible pond pump (2.8m head, 2800L/H flow).
|-
|}
====Manuals====
* [http://www.scottware.net/Lasers/FAQ/FAQ_17/User%20Manual(DSP5.3).pdf LaserCut software manual]
* [[:File:JSM3040N&3060N Manual.pdf | HPC LS3060 hardware manual]]


==Safety information==
==Safety information==
'''<div style="color:red">Please don't touch or fiddle with the laser cutter unless you've have been trained.</div>'''
* '''Don't touch the cooling system without asking first''': overheating or rapid cooling can damage the laser.
* '''Never leave the laser cutter unattended while cutting''': your material may ignite, and an unchecked fire in the laser cutter could be both dangerous and costly. We've also seen mirrors go out of alignment and cut into the cables, This is what a laser cutter fire does to a laser cutter:
 
[[File:lcfire.jpg]]
[[File:lcfire2.jpg]]
 
* '''In case of fire''': use the CO<sub>2</sub> extinguisher by the laser cutter first. Do not use the powder extinguisher unless you feel that you can't control the fire. '''[http://bit.ly/LaserLogbookForm Put it in the logbook] and tell the [[Mailing List]]''': tiny flames while cutting are normal; anything more must be reported.
* '''Never cut PVC or chlorinated plastic''': you should always know what material you are cutting, and chlorinated plastics should be avoided because they release chlorine gas when cut. [[Laser_Cutter/Instructions#Chlorine_Testing_and_Material_Safety|Guidelines for how to test materials.]]
* '''You can't cut metal in the laser cutter''': if you wish to [[Laser_Cutter/Metal|mark the metal]], please use [http://hpclaser.co.uk/index.php?main_page=product_info&cPath=2&products_id=17 Thermark / Cermark], or use anodised aluminium.
 
==Using the laser cutter==
 
# Make sure you're familiar with the [[Laser_Cutter/Instructions|operating instructions]].
# Look up the laser cutter parameters for the material you're using (see bottom of this page).
# Use the [[Media:LHS-Laser-Cutter-Checklist.pdf|LHS Laser Cutter Checklist]] to ensure that you don't forget anything important as you cut.
# [http://bit.ly/LaserLogbookForm Log your use] to help with the upkeep of the lasercutter. (Records can be viewed [http://bit.ly/LaserLogbook here].)
# Pay for your usage - the cost is £5 per hour, which is just enough to cover our [[Laser Cutter/Maintenance|maintenance costs]].
 
==List of allowed and banned materials ==
'''Allowed'''
* MDF (up to 4mm)
* Plywood (Up to 6mm) ''Note: Denser/poor quality ply will have trouble cutting deeper than 4mm, use poplar or another less dense ply for 6mm''
* Balsa wood
* Non-resinous wood IE hardwood (Engraving only)
* Paper (Cut only, don't engrave)
* Card/Cardboard
* Acrylic (up to 10mm)
* Foamcore (non-PVC variety)
* Anodized Aluminium (Engrave only)
 
'''Banned'''
* Food
* Body parts
* Plastics containing PVC
* Plastics containing ABS
* Fibreglass
* Glass
* Circuit boards
* Polycarbonate
* All metal (except anodized aluminium)
 
You should only be cutting materials on the Allowed list, if you want to cut a material which is not on this list, contact one of the trainers and get them to OK it first.
 
== Trainers and maintainers ==
 
If you have questions or problems with the laser cutter, please speak to one of these people:
 
* [[User:Solexious|Solexious]] ([[User talk:Solexious|talk]])
* [[User:Yetifiasco|Yetifiasco]] ([[User Yetifiasco|talk]])
 
==Resources==


* '''Please don't affect the cooling system without consultation''' - overheating or rapid cooling can damage the laser.
* [http://hack.rs/cacti/graph_view.php?action=tree&tree_id=7 Coolbot temperature graph]
* '''Never leave the laser cutter unattended''' - Your material may ignite, and an unchecked fire in the laser cutter could be both dangerous and costly.
* We're currently trying to [[Projects/RELaserSoftware|reverse engineer]] the [[Equipment/LaserCutter/Software|software]].
* '''In case of fire''' - Use the CO<sub>2</sub> extinguisher by the laser cutter first. Do not use the powder extinguisher unless you feel that you can't control the fire.
* Information about additional useful bits of software installed on the machine can be found on the [[Equipment/LaserCutter/Software|software page]].
* '''Never cut PVC or chlorinated plastic''' - You should always know what material you are cutting, and chlorinated plastics should be avoided because they release chlorine gas when cut.
* '''Do not try to cut metal in the laser cutter''' - If you wish to mark the metal, please use [http://hpclaser.co.uk/index.php?main_page=product_info&cPath=2&products_id=17 "Thermark Laser Engraving Spray / Paste"], or use anodised aluminium.


==Instructions==
==Consumables==
These instructions are intended as a companion to [[Workshops#Regular_Hackspace_workshops|laser cutter safety training]] - not a replacement.
* [http://www.plasticonline.co.uk/ Plastic Online]
====Powering on====
* [http://hpclaser.co.uk/index.php?main_page=index&cPath=3&zenid=b68f5a7bd4307cba7fc3822122b2e661 HPC sheet products] - Laser ply, perspex, engraving laminate - where we purchased the cutter.
# Insert key and turn - the PC is turned on using the 'sleep' button on the keyboard.
* [http://www.theplasticshop.co.uk/ The Plastics Shop] - [[User:MattP|mattp]] purchased the plastic for the first batch of [[Media:Laser-cut-key-rings.jpg|Hackspace key rings]] from here.
# '''Always''' perform the following pre-checks:
* [http://hamaracrylic.co.uk Hamar Acrylic] Cuts to size, and is ~10mins walk from the space. Order at the desk and it should be cut to size within minutes.
## Check that there is a '''CO<sub>2</sub>''' fire extinguisher '''immediately to hand'''.
** Price guide 320x600x4mm (laser bed size) clear acrylic = £8 + VAT (=£9.60).
## Check that the water pump is running
* [http://www.acrylic-online.co.uk/ Acrylic-Online] - [[User:Teabot|Elliot]] has bought some Palglas from here. They cut to size - delivery £8.00. Price guide (incl. VAT):
## Check that the extractor fan is on
** 320x600x4mm (laser bed size) clear acrylic (Palglas) = £5.12
# '''Caution:''' Be certain that the water coolant is at a suitable temperature.
* [http://www.hobarts.com/store/ Hobart Laserables] - wide range of materials: MDF, Birch, Acrylic (clear and coloured), Rubber, Laminates, Anodised metal. Prices seem competitive. [[Nigle]] has ordered from here. Shipping is £12.
#* If you are unsure if the cutter has been '''used recently''', or you have been using the cutter for an '''extended period of time''' (an hour or so) check the temperature of the water using the infra-red thermometer.
* [http://www.fredaldous.co.uk Fred Aldous] – online craft supplies, free delivery on orders > £30. Polypropylene sheets amongst other things. Alex P has ordered from here.
#* If the water temperature is outside the acceptable operating range (22 &plusmn; 3 &deg;C) then wait for the water to cool before using the cutter.
* [http://modelshop.co.uk/ 4D ModelShop] is not too far from the space, and is open Saturdays. They offer laser cutting too, and hence seem to have a lot of suitable materials. Helpful staff and a good selection.
* [http://www.blueprintmodel.co.uk/ Blueprint Modelshop] There's a commercial laser cutter service 10 mins from the space, DIY service is £30/h (as of 2013). You can buy acrylic there, but it's coated with horrible sticky paper rather than easy-to-peal plastic.  Beware.


====Preparing your design====
==Manuals==
* Start the 'LaserCut' application and load/import your design.
* [https://www.bosslaser.com/images/pdf/User%20ManualDSP5.3LaserCut53.pdf LaserCut software manual]
* '''TODO''' Different file types pros/cons
* [[:File:JSM3040N&3060N Manual.pdf | HPC LS3060 hardware manual]]
** DXF is nice because it maintains absolute dimensions.
* [http://www.leetro.com/english/down/MPC6515%20%20Manual.pdf Controller manual]
* Sometimes it's useful scale your design. The Laser cutter application allows for this but it's rather quirky:
* [[Equipment/LaserCutter/LogBook|Maintainers Logbook]]
** From the Laser software menu select 'Tools/Size'
** Calculate and enter your new widths/heights in Google/calc etc.
* Rotating
** Go to 'Draw/rotal'
** Enter the number of degrees to rotate
* Uniting lines (making the path finding suck a little less)use this if you've used lines rather than polylines is qcad etc.
** Go to 'Tools/Unite lines'
** Use the defaults
** You should see fewer direction lines, the laser cutter should use a less insane route now.
* The work-area in the LaserCut software is not an absolute representation of the laser cutter bed. The origin must be set relative to your design.
** From the LaserCut application menu select [[:File:Laser-Cutter-Screen-Origin-1.png|'Laser/Set laser origin']]
** Move the 'target' cursor and click on the location on your design where you wish to position the origin (this is usually at the top right of the design)
** You may also [[:File:Laser-Cutter-Screen-Origin-2.png|manually enter the position]] - the top corner of bed is located at (299, 559)
* Layers can be used in your design to provide combinations of different cut types and engrave options on a single piece. For example you may wish to cut out a key-ring and then engrave a name on it.
** Each layer can be assigned different action, speed and power settings - consult the manual or the [[#Parameters_for_different_materials|wiki]] for appropriate settings.
** Finer control of layer power and speed settings is available by [[:File:Laser-Cutter-Screen-Cut-options.png|clicking on the layer]]
* '''Engraving''':
** Try to align the bulk of the engraving with the short axis (y), the laser cutter seems to do passes in this direction only so if you have it aligned to the long (x) axis it will do many short passes rather than fewer longer ones, this can '''massively''' increase engraving time (minutes -> hours)
** Rather than slow down/increase power there is a setting to repeat a layer multiple times, this is very useful if using the engrave option to reach a certain depth.
** For past prototypes the engraving step size can be changed (default is 0.1mm) a setting of 0.2 is good for depth engraving, again this can speed up the process a lot.
* '''Note''' if something hasn't cut/engraved to the complete depth (or you just want to run it again) it is possible to select which layers are 'output' by scrolling to the right in the layers box, this is very useful for an extra layer of engraving or to confirm a full cut. DON'T move the sheet before doing this.


====Uploading your data file====
==More information==
* Upload the file to the design and settings to the laser cutter hardware as follows:
* How the [[Equipment/LaserCutter/CoolBot|cooling system]] works
** Select the [[:File:Laser-Cutter-Screen-Download.png|'Download' button]]
* Some useful [http://www.ladyada.net/library/laser/index.html laser info from Adafruit] - the settings section in particular gave a good idea of what we can expect.
** Remove any existing files by selecting them and clicking 'Del all'
* More information about the controller card used by the cutter  
** Download (upload) your file by clicking 'Download current'
** http://www.leetro.com/english/sale/20.html
** You should hear the laser cutter machine beep.
** http://www.leetro.com/english/sale/23.html
** [http://www.jqlaser.com/service/service.html Latest version of the software]
** [http://www.leetro.com/english/down/59.html Firmware for MPC6515 controller and software] (hit the download page for latest version)
* For making boxes you can use:
** [http://www.thingiverse.com/thing:404 this script] - recommended settings of "--bolt_length 13 --nut_multiplier 1.8" YMMV
** [http://rahulbotics.com/personal-projects/boxmaker/?boxmaker/ BoxMaker] is also _very_ good for making boxes.
** [http://www.keppel.demon.co.uk/111000/111000.html BoxMake] Inkscape plugin
* [http://www.ribbonsoft.com/qcad.html QCAD] - open source .dxf exporting 2D CAD program
* Using Google [[Guides/SketchUp for Laser Cutting|SketchUp for Laser Cutter]] designs.
* A [http://oplaser.co.uk/opsupport/viewforum.php?f=22&sid=730902927827c6ce9aefaa2d085ea9f1 support forum] with various guides
* [[Etching my Macbook Air]]
===Other Hackspace wikis===
* [http://wiki.edinburghhacklab.com/lasercutter Edinburgh Hackspace's Lasercutter] is the same model, so some useful notes over there.
* [https://wiki.nottinghack.org.uk/wiki/Laser_cutter/LaserCut/Usage NottinHack's LaserCut] software write up is quite comprehensive.


====Positioning your material====
==Laser Cutter Parameters - Background==
* '''Caution:''' Know your material - be absolutely certain that your material is safe to use in the laser cutter. If in doubt - ask. For unidentified plastics try [http://www.nycresistor.com/2008/08/28/how-to-identify-polymers-with-burnination/ this test method].
===Thick Material===
* '''Caution:''' There are a number of electrically live areas inside the cabinet towards the back. Be very careful when reaching around at the back as you may get a shock.
Do not try to cut anything thicker than the thickest width listed for that material on this page.
* Place the material on the cutter bed.
===Corner Power===
* The bed height must be adjusted to the thickness of your material. Different materials should have the beam focussed in different places. Thicker materials should have the beam focussed in the middle of the material. You can adjust where the beam focuses by adjusting the bed height:
When the path goes round curves, or a straight line passes close to previous line (TBC), the laser will slow down. As a consequence, the Corner Power needs to be lower to compensate. Typically about 80% of the Power setting.
** Press the 'Z' button on the [[:File:Laser-Cutter-Screen-Z-Axis.jpg|control panel]].
===Lowest power===
** The display will show 'Z-Axis operate'
Setting the power below 10 or 11 means that the laser will not activate.
** Then press the 'Datum' button
===Tried but DIY parameters===
** The display should now show 'Z-Axis datum' and the bed will move to the 0 point. Now you use the up and down buttons to move the bed.
Laser rubber has been used (mainly for stamps) it works well but you'll need to experiment for engraving/cutting. Check out [[Laser_Cutter/Parameters#GradeEngrave]], which is useful for rubber stamps.
* To make sure that your design will be cut within the boundary of your material you can have the cutter mark out the bounding box with the red-dot pointer. Note that you must upload your design to the cutter before doing this.
** Click the [[:File:Laser-Cutter-Screen-Run-box.png|'Run box' button ]] in the laser cutter application
** Observe the path of the red-dot pointer


====Cutting====
==Parameters==
* '''Caution:''' Never leave the machine unattended. The laser cuts and engraves by burning the material so '''you must be present''' to deal with any fires should this process undesirably escalate.
===Cutting===
* Turn on the air pump on the [[:File:Laser-Cutter-Screen-Control-panel.jpg|main control panel]]
====Acrylic - Perspex====
* To begin cutting press the [[:File:Laser-Cutter-Screen-Start.png|'Start' button]] in the laser cutter application.
{| border="1"
* Monitoring progress
!|Thickness (mm)
** '''TODO''' What to watch out for
!|Speed (mm/sec)
** '''TODO''' What to do in case of problems
!|Power (%)
* '''TODO''' What to try if the result is not what you expect
!|Corner power (%)
* Log your Laser Cutter use in the [[Equipment/LaserCutter/LogBook|logbook]]
!|Examples / Notes
|-
|3
|6
|100
|
|
|-
|4
|3.5
|100
|21
|
|-
|5
|3
|100
|
|
|-
|10
|1 (not enough?)
|100
|
|
|}


==Parameters for different materials==
====PLY====
If you found some sweet settings please share them here.
====Cutting====
{| border="1"
{| border="1"
!|Material
!|Thickness (mm)
!|Thickness (mm)
!|Speed (mm/sec)
!|Speed (mm/sec)
!|Power (%)
!|Power (%)
!|Corner power (%)
!|Corner power (%)
!|Examples
!|Examples / Notes
|-
|.5
|25
|80
|
| This seemed to work really well with not much burn on the edges for the super thin ply.
|-
|1.5
|8
|100
|
|
|-
|-
|Ply wood
|3
|3
|?
|5
|?
|100
|?
|
|
|-
|5
|2
|100
|
|
|-
|6
|1
|100
|
|
|
|}
====MDF====
{| border="1"
!|Thickness (mm)
!|Speed (mm/sec)
!|Power (%)
!|Corner power (%)
!|Examples / Notes
|-
|-
|MDF
|3
|3
|4
|5
|100
|100
|20
|20
|
|
|-
|-
|Acrylic - Perspex
|4
|4
|3.5
|4
|100
|100
|21
|
|
|
|}
====Misc====
{| border="1"
!|Material
!|Thickness (mm)
!|Speed (mm/sec)
!|Power (%)
!|Corner power (%)
!|Examples / Notes
|-
|-
|Acrylic - Palglas
|Acrylic - Palglas
Line 157: Line 260:
|21
|21
|[[:File:Teabot-Cubauble.jpg|Cubauble]]
|[[:File:Teabot-Cubauble.jpg|Cubauble]]
|-
|Corrugated Cardboard
|3
|12
|100
|
|
|-
|Hardboard
|3
|3
|100
|
|
|-
|Paper
|
|60
|15
|
|
|-
|Card
|
|35
|40
|
|
|-
|Mountboard
|
|12
|100
|
|
|-
|Engraving Laminate
|
|15
|80
|
|
|-
|Funky Foam
|
|25
|25
|
|
|-
|Curian
|
|1
|100
|
|Four passes required
|-
|Laser Rubber
|
|6
|100
|25
|
|-
|-
|Suede
|Suede
Line 165: Line 331:
|
|
|-
|-
|Suede/Leather (line engraving)
|>1
|150
|10
|10
|
|-
|Leather
|3
|4
|100
|100 (needs more testing)
|
|-
|Full grain leather
|3
|9
|85
|85
|Burn free result! Helps to put tape over leather.
|-
|LD45 Plastazote
|12
|25
|100
|20
|
|-
|[http://www.rapidonline.com/Tools-Fasteners-Production-Equipment/Enclosures/ABS-Boxes/ABS-Boxes-with-transparent-lids/62566 Unknown clear thermoplastic]
|4
|10
|10 - 15
|10
|These box lids melt easily but can be cut with multiple passes at low power.
|-
|Polypropylene sheet
|500micron (0,5mm)
|14
|40
|17
|
|-
|Polypropylene sheet - scoring
|500micron (0,5mm)
|60
|60
|15
| This will produce a score. useful if you want just to mark a point or fold.
|
|-
| Polyester "paper" - NeverTear
|300micron (0.3mm)
|40
|60
|40
| Never tear is a polyester sheet that can be laser printed like normal paper.
|
|-
| Polyester "paper" - NeverTear - Scoring
|300micron (0.3mm)
|100
|15
|40
| This will produce a score. useful if you want just to mark a point or fold.
|}
|}


====Engraving====
===Engraving===
{| border="1"
{| border="1"
!|Material
!|Material
Line 174: Line 404:
!|Corner power (%)
!|Corner power (%)
!|Examples
!|Examples
|-
|Acrylic - Perspex
|200
|21
|
|
|-
|Birch PLY
|200
|17
|
|
|-
|MDF
|200
|25
|
|
|-
|Corrugated Cardboard
|200
|20
|
|
|-
|Hardboard
|200
|20
|
|
|-
|Paper
|200
|15
|
|
|-
|Card
|300
|20
|
|
|-
|Mountboard
|200
|20
|
|
|-
|Engraving Laminate
|200
|21
|
|
|-
|Curian
|3
|100
|
|
|-
|Laser Rubber
|200
|70
|
|
|-
|-
|Anodized aluminium (dyed black)
|Anodized aluminium (dyed black)
Line 192: Line 488:
|80
|80
|
|
|-
|LD45 Plastazote
|200
|10
|10
|At 10% engraves 2-3mm deep. Laser doesn't seem to come on at all at 5% or engrave at speeds >200 mm/s so may not be possible to engrave less deeply than this.
|-
|-
|}
|}


==Consumables==
=== GradeEngrave ===
* [http://www.plasticonline.co.uk/ Plastic Online]
* [http://hpclaser.co.uk/index.php?main_page=index&cPath=3&zenid=b68f5a7bd4307cba7fc3822122b2e661 HPC sheet products] - Laser ply, perspex, engraving laminate - where we purchased the cutter.
* [http://www.theplasticshop.co.uk/ The Plastics Shop] - [[User:MattP|mattp]] purchased the plastic for the first batch of [[Media:Laser-cut-key-rings.jpg|Hackspace key rings]] from here.
* [http://hamaracrylic.co.uk Hamar Acrylic] Cuts to size, and is ~10mins walk from the space. Order by phone and it should be cut and ready to collect on arrival.
**Price guide 320x600x4mm (laser bed size) clear acrylic = £8.
* [http://www.acrylic-online.co.uk/ Acrylic-Online] - [[User:Teabot|Elliot]] has bought some Palglas from here. They cut to size - delivery £8.00. Price guide (incl. VAT):
** 320x600x3mm (laser bed size) clear acrylic (Palglas) = £3.84
** 320x600x4mm (laser bed size) clear acrylic (Palglas) = £5.12
** 320x600x5mm (laser bed size) clear acrylic (Palglas) = £6.29


===Guide For bulk order Quote===
[[File:GradeEngrave-stamp.jpg|thumb|What happens when you use GradeEngrave]]
(bed size sheets)


====Acrylic (perspex)====
Grade Engrave will cause an area inside a engraved area to have raised edges. It is intended for easier rubber stamp making but can be applied to any real use. See the [https://wiki.nottinghack.org.uk/wiki/Laser_cutter/LaserCut/Usage#Grade_Engrave Nottinghack wiki] for more details.
*Clear:
** 10 x 1.5mm
** 10 x 3mm
** 10 x 5mm
** 5 x 10mm


*Solid: Black:
{| border="1"
** 10 x 1.5mm
!|Material
** 10 x 3mm
!|Speed (mm/sec)
** 10 x 5mm
!|Power (%)
 
!|Corner power (%)
*Solid: Red, Blue (ea):
!|Examples
** 5 x 1.5mm
|-
** 5 x 3mm
|Dette's 2.3mm Laserable Rubber Sheets
** 5 x 5mm
|200
 
|70
== Running cost ==
|
 
| Two passes might work better :)
*The tube is £200 for 1000 hours
|-
*The lens+mirrors are £150 for 250 hours
|}
*The power is (say) 1.2kW at £.2/kWh.
*So 200/1000 + 150/250 + 1.2*.2 = £1.04/hour


'''Therefore a recommended donation of £1 for each hour of use would be greatly appreciated.'''


==More information==
[[Category:Tools for use on wood]]
* Some useful [http://www.ladyada.net/library/laser/index.html laser info from Adafruit] - the settings section in particular gave a good idea of what we can expect.
[[Category:Tools for use on plastic]]
* More information about the controller card used by the cutter
** http://www.leetro.com/english/sale/20.html
** http://www.leetro.com/english/sale/23.html
** [http://www.jqlaser.com/service/service.html Latest version of the software]
** [http://www.leetro.com/english/down/59.html Firmware for MPC6515 controller and software] (hit the download page for latest version)
* For making boxes, you can use [http://www.thingiverse.com/thing:404 this script] - recommended settings of "--bolt_length 13 --nut_multiplier 1.8" YMMV
* http://rahulbotics.com/personal-projects/boxmaker/?boxmaker/ is also _very_ good for making boxes.
* [http://www.ribbonsoft.com/qcad.html QCAD] - open source .dxf exporting 2D CAD program

Latest revision as of 00:43, 23 December 2015

Laser cutter
Laser-cutter-installed.jpg
Model HPC LS3060
Sub-category Defunct
Status Unknown
Consumables Unknown
Accessories Coolbot
Training requirement Yes
Training link Training Roster
ACnode No
Owner LHS
Origin Pledge
Location Ground floor, main room
Maintainers Solexious, Yetifiasco
NOTE: This is our old laser cutter which has now been replaced with the Silvertail A0 Laser Cutter. This page is left here for reference.

We have a HPC LS3060 laser engraver and cutter, with a cutting area of 300mm x 560mm. Trained members can use it for the very reasonable rate of £5 per hour.

This cutter was sold.

Laser-cut-key-rings.jpg


Training

You must not use the laser cutter without being trained. The laser cutter is unlikely to hurt you, but you can easily hurt it without training.

Training is given most Wednesdays or Thursdays at around 8pm, is free to attend and available to all members but your place needs to be pre-booked. Space is strictly limited per session so you need to reserve a spot on the Training Roster when a session is available - watch the Mailing List for announcements. Reserving a spot is on a first come first serve so you'll need to be quick. If you can't attend your training session please remove your name from the roster and inform the Mailing List, this will save wasting people's time and can allow a last minute replacement to take your slot.

Training is currently limited to members only but this may change in the future.

A good way to get notified of new training sessions is to go to the roster page, add it to your wiki page Watch list, and modify your wiki account preferences so that you receive emails when pages you Watch get modified.

Feel free to ask for help on the Mailing List, but please read the FAQ first

Costs

  • Training - Free
  • Usage - £5/hour
  • Consumables - Bring your own and/or use what is in the off cuts bin, but always ensure (rather than assume) it's laser safe.

Safety information

  • Don't touch the cooling system without asking first: overheating or rapid cooling can damage the laser.
  • Never leave the laser cutter unattended while cutting: your material may ignite, and an unchecked fire in the laser cutter could be both dangerous and costly. We've also seen mirrors go out of alignment and cut into the cables, This is what a laser cutter fire does to a laser cutter:

Lcfire.jpg Lcfire2.jpg

  • In case of fire: use the CO2 extinguisher by the laser cutter first. Do not use the powder extinguisher unless you feel that you can't control the fire. Put it in the logbook and tell the Mailing List: tiny flames while cutting are normal; anything more must be reported.
  • Never cut PVC or chlorinated plastic: you should always know what material you are cutting, and chlorinated plastics should be avoided because they release chlorine gas when cut. Guidelines for how to test materials.
  • You can't cut metal in the laser cutter: if you wish to mark the metal, please use Thermark / Cermark, or use anodised aluminium.

Using the laser cutter

  1. Make sure you're familiar with the operating instructions.
  2. Look up the laser cutter parameters for the material you're using (see bottom of this page).
  3. Use the LHS Laser Cutter Checklist to ensure that you don't forget anything important as you cut.
  4. Log your use to help with the upkeep of the lasercutter. (Records can be viewed here.)
  5. Pay for your usage - the cost is £5 per hour, which is just enough to cover our maintenance costs.

List of allowed and banned materials

Allowed

  • MDF (up to 4mm)
  • Plywood (Up to 6mm) Note: Denser/poor quality ply will have trouble cutting deeper than 4mm, use poplar or another less dense ply for 6mm
  • Balsa wood
  • Non-resinous wood IE hardwood (Engraving only)
  • Paper (Cut only, don't engrave)
  • Card/Cardboard
  • Acrylic (up to 10mm)
  • Foamcore (non-PVC variety)
  • Anodized Aluminium (Engrave only)

Banned

  • Food
  • Body parts
  • Plastics containing PVC
  • Plastics containing ABS
  • Fibreglass
  • Glass
  • Circuit boards
  • Polycarbonate
  • All metal (except anodized aluminium)

You should only be cutting materials on the Allowed list, if you want to cut a material which is not on this list, contact one of the trainers and get them to OK it first.

Trainers and maintainers

If you have questions or problems with the laser cutter, please speak to one of these people:

Resources

Consumables

  • Plastic Online
  • HPC sheet products - Laser ply, perspex, engraving laminate - where we purchased the cutter.
  • The Plastics Shop - mattp purchased the plastic for the first batch of Hackspace key rings from here.
  • Hamar Acrylic Cuts to size, and is ~10mins walk from the space. Order at the desk and it should be cut to size within minutes.
    • Price guide 320x600x4mm (laser bed size) clear acrylic = £8 + VAT (=£9.60).
  • Acrylic-Online - Elliot has bought some Palglas from here. They cut to size - delivery £8.00. Price guide (incl. VAT):
    • 320x600x4mm (laser bed size) clear acrylic (Palglas) = £5.12
  • Hobart Laserables - wide range of materials: MDF, Birch, Acrylic (clear and coloured), Rubber, Laminates, Anodised metal. Prices seem competitive. Nigle has ordered from here. Shipping is £12.
  • Fred Aldous – online craft supplies, free delivery on orders > £30. Polypropylene sheets amongst other things. Alex P has ordered from here.
  • 4D ModelShop is not too far from the space, and is open Saturdays. They offer laser cutting too, and hence seem to have a lot of suitable materials. Helpful staff and a good selection.
  • Blueprint Modelshop There's a commercial laser cutter service 10 mins from the space, DIY service is £30/h (as of 2013). You can buy acrylic there, but it's coated with horrible sticky paper rather than easy-to-peal plastic. Beware.

Manuals

More information

Other Hackspace wikis

Laser Cutter Parameters - Background

Thick Material

Do not try to cut anything thicker than the thickest width listed for that material on this page.

Corner Power

When the path goes round curves, or a straight line passes close to previous line (TBC), the laser will slow down. As a consequence, the Corner Power needs to be lower to compensate. Typically about 80% of the Power setting.

Lowest power

Setting the power below 10 or 11 means that the laser will not activate.

Tried but DIY parameters

Laser rubber has been used (mainly for stamps) it works well but you'll need to experiment for engraving/cutting. Check out Laser_Cutter/Parameters#GradeEngrave, which is useful for rubber stamps.

Parameters

Cutting

Acrylic - Perspex

Thickness (mm) Speed (mm/sec) Power (%) Corner power (%) Examples / Notes
3 6 100
4 3.5 100 21
5 3 100
10 1 (not enough?) 100

PLY

Thickness (mm) Speed (mm/sec) Power (%) Corner power (%) Examples / Notes
.5 25 80 This seemed to work really well with not much burn on the edges for the super thin ply.
1.5 8 100
3 5 100
5 2 100
6 1 100

MDF

Thickness (mm) Speed (mm/sec) Power (%) Corner power (%) Examples / Notes
3 5 100 20
4 4 100

Misc

Material Thickness (mm) Speed (mm/sec) Power (%) Corner power (%) Examples / Notes
Acrylic - Palglas 3 6 100 21 Cubauble
Corrugated Cardboard 3 12 100
Hardboard 3 3 100
Paper 60 15
Card 35 40
Mountboard 12 100
Engraving Laminate 15 80
Funky Foam 25 25
Curian 1 100 Four passes required
Laser Rubber 6 100 25
Suede 1 25 100 25
Suede/Leather (line engraving) >1 150 10 10
Leather 3 4 100 100 (needs more testing)
Full grain leather 3 9 85 85 Burn free result! Helps to put tape over leather.
LD45 Plastazote 12 25 100 20
Unknown clear thermoplastic 4 10 10 - 15 10 These box lids melt easily but can be cut with multiple passes at low power.
Polypropylene sheet 500micron (0,5mm) 14 40 17
Polypropylene sheet - scoring 500micron (0,5mm) 60 60 15 This will produce a score. useful if you want just to mark a point or fold.
Polyester "paper" - NeverTear 300micron (0.3mm) 40 60 40 Never tear is a polyester sheet that can be laser printed like normal paper.
Polyester "paper" - NeverTear - Scoring 300micron (0.3mm) 100 15 40 This will produce a score. useful if you want just to mark a point or fold.

Engraving

Material Speed (mm/sec) Power (%) Corner power (%) Examples
Acrylic - Perspex 200 21
Birch PLY 200 17
MDF 200 25
Corrugated Cardboard 200 20
Hardboard 200 20
Paper 200 15
Card 300 20
Mountboard 200 20
Engraving Laminate 200 21
Curian 3 100
Laser Rubber 200 70
Anodized aluminium (dyed black) 450 90 ? LHS logo on black phone
Anodized aluminium (Macbook Pro) (Vector - in "cut" mode) 100 100 80 Russ's Macbook Pro
Suede 250 15 80
LD45 Plastazote 200 10 10 At 10% engraves 2-3mm deep. Laser doesn't seem to come on at all at 5% or engrave at speeds >200 mm/s so may not be possible to engrave less deeply than this.

GradeEngrave

What happens when you use GradeEngrave

Grade Engrave will cause an area inside a engraved area to have raised edges. It is intended for easier rubber stamp making but can be applied to any real use. See the Nottinghack wiki for more details.

Material Speed (mm/sec) Power (%) Corner power (%) Examples
Dette's 2.3mm Laserable Rubber Sheets 200 70 Two passes might work better :)
Retrieved from ‘https://wiki.london.hackspace.org.uk/w/index.php?title=Equipment/HPC_LS3060_Laser_Cutter&oldid=48693’